Исходное сообщение
"Не загружается FW для платы TT-premium S-2300" Отправлено Rom1, 27-Авг-08 10:01
Debian/Linux 2.6.18-6-686 В систему установлено 3 карты SS2 и одна TT-premium S-2300. Скайстары загружаются нормально и работают, а технотренд не могу прогрузить... В /lib/firmware пробывал по очереди ложить все загрузчики (dvb-ttpci-01.fw-261a, dvb-ttpci-01.fw-261b, dvb-ttpci-01.fw-261c, dvb-ttpci-01.fw-261d, dvb-ttpci-01.fw-261f, dvb-ttpci-01.fw-2622 и dvb-ttpci-01-f12623-patched.fw) ни с одним не заработало. В логах вот что: - - - - - - - - - - b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 185 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:09:b9:e6 Linux video capture interface: v2.00 saa7146: register extension 'dvb'. b2c2-flexcop: found the stv0299 at i2c address: 0x68 DVB: registering frontend 0 (ST STV0299 DVB-S)... b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 22 (level, low) -> IRQ 217 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:0f:4c:26 b2c2-flexcop: found the stv0299 at i2c address: 0x68 DVB: registering frontend 1 (ST STV0299 DVB-S)... b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete flexcop-pci: will use the HW PID filter. flexcop-pci: card revision 2 ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 185 input: ImPS/2 Generic Wheel Mouse as /class/input/input2 DVB: registering new adapter (FlexCop Digital TV device). b2c2-flexcop: MAC address = 00:d0:d7:13:69:b0 ts: Compaq touchscreen protocol output b2c2-flexcop: found the stv0299 at i2c address: 0x68 DVB: registering frontend 2 (ST STV0299 DVB-S)... b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete --------------------- ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 21 (level, low) -> IRQ 201 saa7146: found saa7146 @ mem e098e000 (revision 1, irq 201) (0x13c2,0x000e). DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.3). adapter has MAC addr = 00:d0:5c:63:a8:df dvb-ttpci: load_dram(): timeout at block 0 dvb-ttpci: av7110_bootarm(): load_dram() failed ACPI: PCI interrupt for device 0000:02:05.0 disabled --------------------- - - - - - - - - - - Вопросы вызываю эти строчки: dvb-ttpci: load_dram(): timeout at block 0 dvb-ttpci: av7110_bootarm(): load_dram() failed Не грузит, а почему?

Ваше сообщение
Имя*:
EMail:	Для отправки новых сообщений в текущей нити на email укажите знак ! перед адресом, например, [email protected] (!! - не показывать email). Более тонкая настройка отправки ответов производится в профиле зарегистрированного участника форума.
Заголовок*:
Сообщение*:	> Debian/Linux 2.6.18-6-686 > В систему установлено 3 карты SS2 и одна TT-premium S-2300. Скайстары загружаются > нормально и работают, а технотренд не могу прогрузить... > В /lib/firmware пробывал по очереди ложить все загрузчики (dvb-ttpci-01.fw-261a, dvb-ttpci-01.fw-261b, > dvb-ttpci-01.fw-261c, dvb-ttpci-01.fw-261d, dvb-ttpci-01.fw-261f, dvb-ttpci-01.fw-2622 > и dvb-ttpci-01-f12623-patched.fw) ни с одним не заработало. > В логах вот что: > - - - - - - - - - - > b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully > flexcop-pci: will use the HW PID filter. > flexcop-pci: card revision 2 > ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 185 > DVB: registering new adapter (FlexCop Digital TV device). > b2c2-flexcop: MAC address = 00:d0:d7:09:b9:e6 > Linux video capture interface: v2.00 > saa7146: register extension 'dvb'. > b2c2-flexcop: found the stv0299 at i2c address: 0x68 > DVB: registering frontend 0 (ST STV0299 DVB-S)... > b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by > a 'FlexCopIIb' complete > flexcop-pci: will use the HW PID filter. > flexcop-pci: card revision 2 > ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 22 (level, low) -> IRQ 217 > DVB: registering new adapter (FlexCop Digital TV device). > b2c2-flexcop: MAC address = 00:d0:d7:0f:4c:26 > b2c2-flexcop: found the stv0299 at i2c address: 0x68 > DVB: registering frontend 1 (ST STV0299 DVB-S)... > b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by > a 'FlexCopIIb' complete > flexcop-pci: will use the HW PID filter. > flexcop-pci: card revision 2 > ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 185 > input: ImPS/2 Generic Wheel Mouse as /class/input/input2 > DVB: registering new adapter (FlexCop Digital TV device). > b2c2-flexcop: MAC address = 00:d0:d7:13:69:b0 > ts: Compaq touchscreen protocol output > b2c2-flexcop: found the stv0299 at i2c address: 0x68 > DVB: registering frontend 2 (ST STV0299 DVB-S)... > b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by > a 'FlexCopIIb' complete > --------------------- > ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 21 (level, low) -> IRQ 201 > saa7146: found saa7146 @ mem e098e000 (revision 1, irq 201) (0x13c2,0x000e). > DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.3). > adapter has MAC addr = 00:d0:5c:63:a8:df > dvb-ttpci: load_dram(): timeout at block 0 > dvb-ttpci: av7110_bootarm(): load_dram() failed > ACPI: PCI interrupt for device 0000:02:05.0 disabled > --------------------- > - - - - - - - - - - > Вопросы вызываю эти строчки: > dvb-ttpci: load_dram(): timeout at block 0 > dvb-ttpci: av7110_bootarm(): load_dram() failed > Не грузит, а почему?
	Введите код, изображенный на картинке: