The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Поиск:  Каталог документации

3.4. Device Names in scsidev

A utility program called scsidev adds device names to the /dev/scsi directory that reflect the SCSI address of each device. The first 2 letters of the name are the upper level SCSI driver name (i.e. either sd, sr, st or sg). The number following the "h" is the host number while the number following the "-" is meant for host identification purposes. For PCI adapters this seems to be always 0 while for ISA adapters it is their IO address. [Perhaps this field could be made more informative or dropped.] The numbers following the "c", "i" and "l" are channel (bus), target id and lun values respectively. Raw disks are shown without a trailing partition number while partitions contained within them are shown with the partition number following a "p".

The scsidev would typically be run as part of the boot up sequence. It may also be useful to run it after the SCSI configuration has changed (e.g. adding or removing lower level driver modules, or the use of the add/remove-single-device command). After scsidev has been run on my system which contains 2 disks, a cd reader and writer plus a scanner, then the following names were added in the /dev/scsi directory:

$ ls -l /dev/scsi/   # abridged
total 0
brw-------  8,   0 Sep  2 11:56 sdh0-0c0i0l0
brw-------  8,   1 Sep  2 11:56 sdh0-0c0i0l0p1
...
brw-------  8,   8 Sep  2 11:56 sdh0-0c0i0l0p8
brw-------  8,  16 Sep  2 11:56 sdh0-0c0i1l0
brw-------  8,  17 Sep  2 11:56 sdh0-0c0i1l0p1
...
brw-------  8,  24 Sep  2 11:56 sdh0-0c0i1l0p8
crw------- 21,   0 Sep  2 11:56 sgh0-0c0i0l0
crw------- 21,   1 Sep  2 11:56 sgh0-0c0i1l0
crw------- 21,   2 Sep  2 11:56 sgh1-0c0i2l0
crw------- 21,   3 Sep  2 11:56 sgh1-0c0i5l0
crw------- 21,   4 Sep  2 11:56 sgh1-0c0i6l0
br-------- 11,   0 Sep  2 11:56 srh1-0c0i2l0
br-------- 11,   1 Sep  2 11:56 srh1-0c0i6l0
The mapping between the SCSI generic device names (sg) and their corresponding names when controlled by other upper level drivers (i.e. sd, sr or st) can be seen by looking for name matches when the second letter is ignored. Hence "sdh0-0c0i0l0" and "sgh0-0c0i0l0" refer to the same device. By process of elimination the "sgh1-0c0i5l0" filename is the scanner since that class of devices can only be accessed via the sg interface.

The scsidev package also includes the ability to introduce names like /dev/scsi/scanner by manipulating the /etc/scsi.alias configuration file. The package also includes the useful rescan-scsi-bus.sh utility. For further information about scsidev see W6. On my system, both devfs and scsidev co-exist happily.




Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру