Author: Maksim Kiselev <[email protected]> Date: Wed Jan 24 10:24:36 2024 +0300 aoe: avoid potential deadlock at set_capacity commit e169bd4fb2b36c4b2bee63c35c740c85daeb2e86 upstream. Move set_capacity() outside of the section procected by (&d->lock). To avoid possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- [1] lock(&bdev->bd_size_lock); local_irq_disable(); [2] lock(&d->lock); [3] lock(&bdev->bd_size_lock); <Interrupt> [4] lock(&d->lock); *** DEADLOCK *** Where [1](&bdev->bd_size_lock) hold by zram_add()->set_capacity(). [2]lock(&d->lock) hold by aoeblk_gdalloc(). And aoeblk_gdalloc() is trying to acquire [3](&bdev->bd_size_lock) at set_capacity() call. In this situation an attempt to acquire [4]lock(&d->lock) from aoecmd_cfg_rsp() will lead to deadlock. So the simplest solution is breaking lock dependency [2](&d->lock) -> [3](&bdev->bd_size_lock) by moving set_capacity() outside. Signed-off-by: Maksim Kiselev <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]> [ Larry: backport to 5.15.y. Minor conflict resolved due to missing commit d9c2bd252a457 aoe: add error handling support for add_disk() ] Signed-off-by: Larry Bassel <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Shengjiu Wang <[email protected]> Date: Wed Jun 25 10:05:04 2025 +0800 ASoC: fsl_asrc: use internal measured ratio for non-ideal ratio mode [ Upstream commit cbe876121633dadb2b0ce52711985328638e9aab ] When USRC=0, there is underrun issue for the non-ideal ratio mode; according to the reference mannual, the internal measured ratio can be used with USRC=1 and IDRC=0. Fixes: d0250cf4f2ab ("ASoC: fsl_asrc: Add an option to select internal ratio mode") Signed-off-by: Shengjiu Wang <[email protected]> Reviewed-by: Daniel Baluta <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Mark Brown <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Fri Jul 4 06:23:53 2025 +0000 atm: clip: Fix infinite recursive call of clip_push(). [ Upstream commit c489f3283dbfc0f3c00c312149cae90d27552c45 ] syzbot reported the splat below. [0] This happens if we call ioctl(ATMARP_MKIP) more than once. During the first call, clip_mkip() sets clip_push() to vcc->push(), and the second call copies it to clip_vcc->old_push(). Later, when the socket is close()d, vcc_destroy_socket() passes NULL skb to clip_push(), which calls clip_vcc->old_push(), triggering the infinite recursion. Let's prevent the second ioctl(ATMARP_MKIP) by checking vcc->user_back, which is allocated by the first call as clip_vcc. Note also that we use lock_sock() to prevent racy calls. [0]: BUG: TASK stack guard page was hit at ffffc9000d66fff8 (stack is ffffc9000d670000..ffffc9000d678000) Oops: stack guard page: 0000 [#1] SMP KASAN NOPTI CPU: 0 UID: 0 PID: 5322 Comm: syz.0.0 Not tainted 6.16.0-rc4-syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:clip_push+0x5/0x720 net/atm/clip.c:191 Code: e0 8f aa 8c e8 1c ad 5b fa eb ae 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 55 <41> 57 41 56 41 55 41 54 53 48 83 ec 20 48 89 f3 49 89 fd 48 bd 00 RSP: 0018:ffffc9000d670000 EFLAGS: 00010246 RAX: 1ffff1100235a4a5 RBX: ffff888011ad2508 RCX: ffff8880003c0000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888037f01000 RBP: dffffc0000000000 R08: ffffffff8fa104f7 R09: 1ffffffff1f4209e R10: dffffc0000000000 R11: ffffffff8a99b300 R12: ffffffff8a99b300 R13: ffff888037f01000 R14: ffff888011ad2500 R15: ffff888037f01578 FS: 000055557ab6d500(0000) GS:ffff88808d250000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc9000d66fff8 CR3: 0000000043172000 CR4: 0000000000352ef0 Call Trace: <TASK> clip_push+0x6dc/0x720 net/atm/clip.c:200 clip_push+0x6dc/0x720 net/atm/clip.c:200 clip_push+0x6dc/0x720 net/atm/clip.c:200 ... clip_push+0x6dc/0x720 net/atm/clip.c:200 clip_push+0x6dc/0x720 net/atm/clip.c:200 clip_push+0x6dc/0x720 net/atm/clip.c:200 vcc_destroy_socket net/atm/common.c:183 [inline] vcc_release+0x157/0x460 net/atm/common.c:205 __sock_release net/socket.c:647 [inline] sock_close+0xc0/0x240 net/socket.c:1391 __fput+0x449/0xa70 fs/file_table.c:465 task_work_run+0x1d1/0x260 kernel/task_work.c:227 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop+0xec/0x110 kernel/entry/common.c:114 exit_to_user_mode_prepare include/linux/entry-common.h:330 [inline] syscall_exit_to_user_mode_work include/linux/entry-common.h:414 [inline] syscall_exit_to_user_mode include/linux/entry-common.h:449 [inline] do_syscall_64+0x2bd/0x3b0 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7ff31c98e929 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fffb5aa1f78 EFLAGS: 00000246 ORIG_RAX: 00000000000001b4 RAX: 0000000000000000 RBX: 0000000000012747 RCX: 00007ff31c98e929 RDX: 0000000000000000 RSI: 000000000000001e RDI: 0000000000000003 RBP: 00007ff31cbb7ba0 R08: 0000000000000001 R09: 0000000db5aa226f R10: 00007ff31c7ff030 R11: 0000000000000246 R12: 00007ff31cbb608c R13: 00007ff31cbb6080 R14: ffffffffffffffff R15: 00007fffb5aa2090 </TASK> Modules linked in: Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: [email protected] Closes: https://syzkaller.appspot.com/bug?extid=2371d94d248d126c1eb1 Signed-off-by: Kuniyuki Iwashima <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Fri Jul 4 06:23:52 2025 +0000 atm: clip: Fix memory leak of struct clip_vcc. [ Upstream commit 62dba28275a9a3104d4e33595c7b3328d4032d8d ] ioctl(ATMARP_MKIP) allocates struct clip_vcc and set it to vcc->user_back. The code assumes that vcc_destroy_socket() passes NULL skb to vcc->push() when the socket is close()d, and then clip_push() frees clip_vcc. However, ioctl(ATMARPD_CTRL) sets NULL to vcc->push() in atm_init_atmarp(), resulting in memory leak. Let's serialise two ioctl() by lock_sock() and check vcc->push() in atm_init_atmarp() to prevent memleak. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Yue Haibing <[email protected]> Date: Sat Jul 5 16:52:28 2025 +0800 atm: clip: Fix NULL pointer dereference in vcc_sendmsg() [ Upstream commit 22fc46cea91df3dce140a7dc6847c6fcf0354505 ] atmarpd_dev_ops does not implement the send method, which may cause crash as bellow. BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: Oops: 0010 [#1] SMP KASAN NOPTI CPU: 0 UID: 0 PID: 5324 Comm: syz.0.0 Not tainted 6.15.0-rc6-syzkaller-00346-g5723cc3450bc #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at 0xffffffffffffffd6. RSP: 0018:ffffc9000d3cf778 EFLAGS: 00010246 RAX: 1ffffffff1910dd1 RBX: 00000000000000c0 RCX: dffffc0000000000 RDX: ffffc9000dc82000 RSI: ffff88803e4c4640 RDI: ffff888052cd0000 RBP: ffffc9000d3cf8d0 R08: ffff888052c9143f R09: 1ffff1100a592287 R10: dffffc0000000000 R11: 0000000000000000 R12: 1ffff92001a79f00 R13: ffff888052cd0000 R14: ffff88803e4c4640 R15: ffffffff8c886e88 FS: 00007fbc762566c0(0000) GS:ffff88808d6c2000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 0000000041f1b000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> vcc_sendmsg+0xa10/0xc50 net/atm/common.c:644 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg+0x219/0x270 net/socket.c:727 ____sys_sendmsg+0x52d/0x830 net/socket.c:2566 ___sys_sendmsg+0x21f/0x2a0 net/socket.c:2620 __sys_sendmmsg+0x227/0x430 net/socket.c:2709 __do_sys_sendmmsg net/socket.c:2736 [inline] __se_sys_sendmmsg net/socket.c:2733 [inline] __x64_sys_sendmmsg+0xa0/0xc0 net/socket.c:2733 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xf6/0x210 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: [email protected] Closes: https://lore.kernel.org/all/[email protected]/T Signed-off-by: Yue Haibing <[email protected]> Reviewed-by: Kuniyuki Iwashima <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Fri Jul 4 06:23:51 2025 +0000 atm: clip: Fix potential null-ptr-deref in to_atmarpd(). [ Upstream commit 706cc36477139c1616a9b2b96610a8bb520b7119 ] atmarpd is protected by RTNL since commit f3a0592b37b8 ("[ATM]: clip causes unregister hang"). However, it is not enough because to_atmarpd() is called without RTNL, especially clip_neigh_solicit() / neigh_ops->solicit() is unsleepable. Also, there is no RTNL dependency around atmarpd. Let's use a private mutex and RCU to protect access to atmarpd in to_atmarpd(). Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Thomas Fourier <[email protected]> Date: Tue Jun 24 08:41:47 2025 +0200 atm: idt77252: Add missing `dma_map_error()` [ Upstream commit c4890963350dcf4e9a909bae23665921fba4ad27 ] The DMA map functions can fail and should be tested for errors. Signed-off-by: Thomas Fourier <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Shravya KN <[email protected]> Date: Thu Jul 10 14:39:36 2025 -0700 bnxt_en: Fix DCB ETS validation [ Upstream commit b74c2a2e9cc471e847abd87e50a2354c07e02040 ] In bnxt_ets_validate(), the code incorrectly loops over all possible traffic classes to check and add the ETS settings. Fix it to loop over the configured traffic classes only. The unconfigured traffic classes will default to TSA_ETS with 0 bandwidth. Looping over these unconfigured traffic classes may cause the validation to fail and trigger this error message: "rejecting ETS config starving a TC\n" The .ieee_setets() will then fail. Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.") Reviewed-by: Sreekanth Reddy <[email protected]> Signed-off-by: Shravya KN <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Somnath Kotur <[email protected]> Date: Thu Jul 10 14:39:38 2025 -0700 bnxt_en: Set DMA unmap len correctly for XDP_REDIRECT [ Upstream commit 3cdf199d4755d477972ee87110b2aebc88b3cfad ] When transmitting an XDP_REDIRECT packet, call dma_unmap_len_set() with the proper length instead of 0. This bug triggers this warning on a system with IOMMU enabled: WARNING: CPU: 36 PID: 0 at drivers/iommu/dma-iommu.c:842 __iommu_dma_unmap+0x159/0x170 RIP: 0010:__iommu_dma_unmap+0x159/0x170 Code: a8 00 00 00 00 48 c7 45 b0 00 00 00 00 48 c7 45 c8 00 00 00 00 48 c7 45 a0 ff ff ff ff 4c 89 45 b8 4c 89 45 c0 e9 77 ff ff ff <0f> 0b e9 60 ff ff ff e8 8b bf 6a 00 66 66 2e 0f 1f 84 00 00 00 00 RSP: 0018:ff22d31181150c88 EFLAGS: 00010206 RAX: 0000000000002000 RBX: 00000000e13a0000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ff22d31181150cf0 R08: ff22d31181150ca8 R09: 0000000000000000 R10: 0000000000000000 R11: ff22d311d36c9d80 R12: 0000000000001000 R13: ff13544d10645010 R14: ff22d31181150c90 R15: ff13544d0b2bac00 FS: 0000000000000000(0000) GS:ff13550908a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005be909dacff8 CR3: 0008000173408003 CR4: 0000000000f71ef0 PKRU: 55555554 Call Trace: <IRQ> ? show_regs+0x6d/0x80 ? __warn+0x89/0x160 ? __iommu_dma_unmap+0x159/0x170 ? report_bug+0x17e/0x1b0 ? handle_bug+0x46/0x90 ? exc_invalid_op+0x18/0x80 ? asm_exc_invalid_op+0x1b/0x20 ? __iommu_dma_unmap+0x159/0x170 ? __iommu_dma_unmap+0xb3/0x170 iommu_dma_unmap_page+0x4f/0x100 dma_unmap_page_attrs+0x52/0x220 ? srso_alias_return_thunk+0x5/0xfbef5 ? xdp_return_frame+0x2e/0xd0 bnxt_tx_int_xdp+0xdf/0x440 [bnxt_en] __bnxt_poll_work_done+0x81/0x1e0 [bnxt_en] bnxt_poll+0xd3/0x1e0 [bnxt_en] Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support") Signed-off-by: Somnath Kotur <[email protected]> Signed-off-by: Michael Chan <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: John Fastabend <[email protected]> Date: Fri Sep 1 13:21:37 2023 -0700 bpf, sockmap: Fix skb refcnt race after locking changes commit a454d84ee20baf7bd7be90721b9821f73c7d23d9 upstream. There is a race where skb's from the sk_psock_backlog can be referenced after userspace side has already skb_consumed() the sk_buff and its refcnt dropped to zer0 causing use after free. The flow is the following: while ((skb = skb_peek(&psock->ingress_skb)) sk_psock_handle_Skb(psock, skb, ..., ingress) if (!ingress) ... sk_psock_skb_ingress sk_psock_skb_ingress_enqueue(skb) msg->skb = skb sk_psock_queue_msg(psock, msg) skb_dequeue(&psock->ingress_skb) The sk_psock_queue_msg() puts the msg on the ingress_msg queue. This is what the application reads when recvmsg() is called. An application can read this anytime after the msg is placed on the queue. The recvmsg hook will also read msg->skb and then after user space reads the msg will call consume_skb(skb) on it effectively free'ing it. But, the race is in above where backlog queue still has a reference to the skb and calls skb_dequeue(). If the skb_dequeue happens after the user reads and free's the skb we have a use after free. The !ingress case does not suffer from this problem because it uses sendmsg_*(sk, msg) which does not pass the sk_buff further down the stack. The following splat was observed with 'test_progs -t sockmap_listen': [ 1022.710250][ T2556] general protection fault, ... [...] [ 1022.712830][ T2556] Workqueue: events sk_psock_backlog [ 1022.713262][ T2556] RIP: 0010:skb_dequeue+0x4c/0x80 [ 1022.713653][ T2556] Code: ... [...] [ 1022.720699][ T2556] Call Trace: [ 1022.720984][ T2556] <TASK> [ 1022.721254][ T2556] ? die_addr+0x32/0x80^M [ 1022.721589][ T2556] ? exc_general_protection+0x25a/0x4b0 [ 1022.722026][ T2556] ? asm_exc_general_protection+0x22/0x30 [ 1022.722489][ T2556] ? skb_dequeue+0x4c/0x80 [ 1022.722854][ T2556] sk_psock_backlog+0x27a/0x300 [ 1022.723243][ T2556] process_one_work+0x2a7/0x5b0 [ 1022.723633][ T2556] worker_thread+0x4f/0x3a0 [ 1022.723998][ T2556] ? __pfx_worker_thread+0x10/0x10 [ 1022.724386][ T2556] kthread+0xfd/0x130 [ 1022.724709][ T2556] ? __pfx_kthread+0x10/0x10 [ 1022.725066][ T2556] ret_from_fork+0x2d/0x50 [ 1022.725409][ T2556] ? __pfx_kthread+0x10/0x10 [ 1022.725799][ T2556] ret_from_fork_asm+0x1b/0x30 [ 1022.726201][ T2556] </TASK> To fix we add an skb_get() before passing the skb to be enqueued in the engress queue. This bumps the skb->users refcnt so that consume_skb() and kfree_skb will not immediately free the sk_buff. With this we can be sure the skb is still around when we do the dequeue. Then we just need to decrement the refcnt or free the skb in the backlog case which we do by calling kfree_skb() on the ingress case as well as the sendmsg case. Before locking change from fixes tag we had the sock locked so we couldn't race with user and there was no issue here. Fixes: 799aa7f98d53e ("skmsg: Avoid lock_sock() in sk_psock_backlog()") Reported-by: Jiri Olsa <[email protected]> Signed-off-by: John Fastabend <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Tested-by: Xu Kuohai <[email protected]> Tested-by: Jiri Olsa <[email protected]> Link: https://lore.kernel.org/bpf/[email protected] Signed-off-by: Pranav Tyagi <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Andrii Nakryiko <[email protected]> Date: Thu Nov 9 16:26:37 2023 -0800 bpf: fix precision backtracking instruction iteration commit 4bb7ea946a370707315ab774432963ce47291946 upstream. Fix an edge case in __mark_chain_precision() which prematurely stops backtracking instructions in a state if it happens that state's first and last instruction indexes are the same. This situations doesn't necessarily mean that there were no instructions simulated in a state, but rather that we starting from the instruction, jumped around a bit, and then ended up at the same instruction before checkpointing or marking precision. To distinguish between these two possible situations, we need to consult jump history. If it's empty or contain a single record "bridging" parent state and first instruction of processed state, then we indeed backtracked all instructions in this state. But if history is not empty, we are definitely not done yet. Move this logic inside get_prev_insn_idx() to contain it more nicely. Use -ENOENT return code to denote "we are out of instructions" situation. This bug was exposed by verifier_loop1.c's bounded_recursion subtest, once the next fix in this patch set is applied. Acked-by: Eduard Zingerman <[email protected]> Fixes: b5dc0163d8fd ("bpf: precise scalar_value tracking") Signed-off-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Alexei Starovoitov <[email protected]> Signed-off-by: Aaron Lu <[email protected]> Reported-by: Wei Wei <[email protected]> Closes: https://lore.kernel.org/all/20250605070921.GA3795@bytedance/ Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Filipe Manana <[email protected]> Date: Fri Jun 20 15:54:05 2025 +0100 btrfs: propagate last_unlink_trans earlier when doing a rmdir [ Upstream commit c466e33e729a0ee017d10d919cba18f503853c60 ] In case the removed directory had a snapshot that was deleted, we are propagating its inode's last_unlink_trans to the parent directory after we removed the entry from the parent directory. This leaves a small race window where someone can log the parent directory after we removed the entry and before we updated last_unlink_trans, and as a result if we ever try to replay such a log tree, we will fail since we will attempt to remove a snapshot during log replay, which is currently not possible and results in the log replay (and mount) to fail. This is the type of failure described in commit 1ec9a1ae1e30 ("Btrfs: fix unreplayable log after snapshot delete + parent dir fsync"). So fix this by propagating the last_unlink_trans to the parent directory before we remove the entry from it. Fixes: 44f714dae50a ("Btrfs: improve performance on fsync against new inode after rename/unlink") Reviewed-by: Johannes Thumshirn <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Filipe Manana <[email protected]> Date: Fri Jun 20 16:37:01 2025 +0100 btrfs: use btrfs_record_snapshot_destroy() during rmdir [ Upstream commit 157501b0469969fc1ba53add5049575aadd79d80 ] We are setting the parent directory's last_unlink_trans directly which may result in a concurrent task starting to log the directory not see the update and therefore can log the directory after we removed a child directory which had a snapshot within instead of falling back to a transaction commit. Replaying such a log tree would result in a mount failure since we can't currently delete snapshots (and subvolumes) during log replay. This is the type of failure described in commit 1ec9a1ae1e30 ("Btrfs: fix unreplayable log after snapshot delete + parent dir fsync"). Fix this by using btrfs_record_snapshot_destroy() which updates the last_unlink_trans field while holding the inode's log_mutex lock. Fixes: 44f714dae50a ("Btrfs: improve performance on fsync against new inode after rename/unlink") Reviewed-by: Johannes Thumshirn <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Sean Nyekjaer <[email protected]> Date: Fri Jul 11 12:12:02 2025 +0200 can: m_can: m_can_handle_lost_msg(): downgrade msg lost in rx message to debug level [ Upstream commit 58805e9cbc6f6a28f35d90e740956e983a0e036e ] Downgrade the "msg lost in rx" message to debug level, to prevent flooding the kernel log with error messages. Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Reviewed-by: Vincent Mailhol <[email protected]> Signed-off-by: Sean Nyekjaer <[email protected]> Link: https://patch.msgid.link/[email protected] [mkl: enhance commit message] Signed-off-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Christian König <[email protected]> Date: Tue Jun 15 15:10:03 2021 +0200 dma-buf: add dma_resv_for_each_fence_unlocked v8 [ Upstream commit c921ff373b469ad7907cde219fa700909f59cac4 ] Abstract the complexity of iterating over all the fences in a dma_resv object. The new loop handles the whole RCU and retry dance and returns only fences where we can be sure we grabbed the right one. v2: fix accessing the shared fences while they might be freed, improve kerneldoc, rename _cursor to _iter, add dma_resv_iter_is_exclusive, add dma_resv_iter_begin/end v3: restructor the code, move rcu_read_lock()/unlock() into the iterator, add dma_resv_iter_is_restarted() v4: fix NULL deref when no explicit fence exists, drop superflous rcu_read_lock()/unlock() calls. v5: fix typos in the documentation v6: fix coding error when excl fence is NULL v7: one more logic fix v8: fix index check in dma_resv_iter_is_exclusive() Signed-off-by: Christian König <[email protected]> Reviewed-by: Tvrtko Ursulin <[email protected]> (v7) Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Stable-dep-of: 2b95a7db6e0f ("dma-buf: fix timeout handling in dma_resv_wait_timeout v2") Signed-off-by: Sasha Levin <[email protected]>
Author: Christian König <[email protected]> Date: Tue Jan 28 10:47:48 2025 +0100 dma-buf: fix timeout handling in dma_resv_wait_timeout v2 [ Upstream commit 2b95a7db6e0f75587bffddbb490399cbb87e4985 ] Even the kerneldoc says that with a zero timeout the function should not wait for anything, but still return 1 to indicate that the fences are signaled now. Unfortunately that isn't what was implemented, instead of only returning 1 we also waited for at least one jiffies. Fix that by adjusting the handling to what the function is actually documented to do. v2: improve code readability Reported-by: Marek Olšák <[email protected]> Reported-by: Lucas Stach <[email protected]> Signed-off-by: Christian König <[email protected]> Reviewed-by: Lucas Stach <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
Author: Christian König <[email protected]> Date: Tue Jun 15 15:28:03 2021 +0200 dma-buf: use new iterator in dma_resv_wait_timeout [ Upstream commit ada5c48b11a3df814701daa9cd11305a75a5f1a5 ] This makes the function much simpler since the complex retry logic is now handled elsewhere. Signed-off-by: Christian König <[email protected]> Reviewed-by: Daniel Vetter <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Stable-dep-of: 2b95a7db6e0f ("dma-buf: fix timeout handling in dma_resv_wait_timeout v2") Signed-off-by: Sasha Levin <[email protected]>
Author: Kaustabh Chakraborty <[email protected]> Date: Fri Jun 27 00:50:30 2025 +0530 drm/exynos: exynos7_drm_decon: add vblank check in IRQ handling commit b846350aa272de99bf6fecfa6b08e64ebfb13173 upstream. If there's support for another console device (such as a TTY serial), the kernel occasionally panics during boot. The panic message and a relevant snippet of the call stack is as follows: Unable to handle kernel NULL pointer dereference at virtual address 000000000000000 Call trace: drm_crtc_handle_vblank+0x10/0x30 (P) decon_irq_handler+0x88/0xb4 [...] Otherwise, the panics don't happen. This indicates that it's some sort of race condition. Add a check to validate if the drm device can handle vblanks before calling drm_crtc_handle_vblank() to avoid this. Cc: [email protected] Fixes: 96976c3d9aff ("drm/exynos: Add DECON driver") Signed-off-by: Kaustabh Chakraborty <[email protected]> Signed-off-by: Inki Dae <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Simona Vetter <[email protected]> Date: Mon Jul 7 17:18:13 2025 +0200 drm/gem: Fix race in drm_gem_handle_create_tail() commit bd46cece51a36ef088f22ef0416ac13b0a46d5b0 upstream. Object creation is a careful dance where we must guarantee that the object is fully constructed before it is visible to other threads, and GEM buffer objects are no difference. Final publishing happens by calling drm_gem_handle_create(). After that the only allowed thing to do is call drm_gem_object_put() because a concurrent call to the GEM_CLOSE ioctl with a correctly guessed id (which is trivial since we have a linear allocator) can already tear down the object again. Luckily most drivers get this right, the very few exceptions I've pinged the relevant maintainers for. Unfortunately we also need drm_gem_handle_create() when creating additional handles for an already existing object (e.g. GETFB ioctl or the various bo import ioctl), and hence we cannot have a drm_gem_handle_create_and_put() as the only exported function to stop these issues from happening. Now unfortunately the implementation of drm_gem_handle_create() isn't living up to standards: It does correctly finishe object initialization at the global level, and hence is safe against a concurrent tear down. But it also sets up the file-private aspects of the handle, and that part goes wrong: We fully register the object in the drm_file.object_idr before calling drm_vma_node_allow() or obj->funcs->open, which opens up races against concurrent removal of that handle in drm_gem_handle_delete(). Fix this with the usual two-stage approach of first reserving the handle id, and then only registering the object after we've completed the file-private setup. Jacek reported this with a testcase of concurrently calling GEM_CLOSE on a freshly-created object (which also destroys the object), but it should be possible to hit this with just additional handles created through import or GETFB without completed destroying the underlying object with the concurrent GEM_CLOSE ioctl calls. Note that the close-side of this race was fixed in f6cd7daecff5 ("drm: Release driver references to handle before making it available again"), which means a cool 9 years have passed until someone noticed that we need to make this symmetry or there's still gaps left :-/ Without the 2-stage close approach we'd still have a race, therefore that's an integral part of this bugfix. More importantly, this means we can have NULL pointers behind allocated id in our drm_file.object_idr. We need to check for that now: - drm_gem_handle_delete() checks for ERR_OR_NULL already - drm_gem.c:object_lookup() also chekcs for NULL - drm_gem_release() should never be called if there's another thread still existing that could call into an IOCTL that creates a new handle, so cannot race. For paranoia I added a NULL check to drm_gem_object_release_handle() though. - most drivers (etnaviv, i915, msm) are find because they use idr_find(), which maps both ENOENT and NULL to NULL. - drivers using idr_for_each_entry() should also be fine, because idr_get_next does filter out NULL entries and continues the iteration. - The same holds for drm_show_memory_stats(). v2: Use drm_WARN_ON (Thomas) Reported-by: Jacek Lawrynowicz <[email protected]> Tested-by: Jacek Lawrynowicz <[email protected]> Reviewed-by: Thomas Zimmermann <[email protected]> Cc: [email protected] Cc: Jacek Lawrynowicz <[email protected]> Cc: Maarten Lankhorst <[email protected]> Cc: Maxime Ripard <[email protected]> Cc: Thomas Zimmermann <[email protected]> Cc: David Airlie <[email protected]> Cc: Simona Vetter <[email protected]> Signed-off-by: Simona Vetter <[email protected]> Signed-off-by: Simona Vetter <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Matthew Brost <[email protected]> Date: Fri Jun 13 14:20:13 2025 -0700 drm/sched: Increment job count before swapping tail spsc queue commit 8af39ec5cf2be522c8eb43a3d8005ed59e4daaee upstream. A small race exists between spsc_queue_push and the run-job worker, in which spsc_queue_push may return not-first while the run-job worker has already idled due to the job count being zero. If this race occurs, job scheduling stops, leading to hangs while waiting on the job’s DMA fences. Seal this race by incrementing the job count before appending to the SPSC queue. This race was observed on a drm-tip 6.16-rc1 build with the Xe driver in an SVM test case. Fixes: 1b1f42d8fde4 ("drm: move amd_gpu_scheduler into common location") Fixes: 27105db6c63a ("drm/amdgpu: Add SPSC queue to scheduler.") Cc: [email protected] Signed-off-by: Matthew Brost <[email protected]> Reviewed-by: Jonathan Cavitt <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Al Viro <[email protected]> Date: Mon Jun 30 02:52:13 2025 -0400 fix proc_sys_compare() handling of in-lookup dentries [ Upstream commit b969f9614885c20f903e1d1f9445611daf161d6d ] There's one case where ->d_compare() can be called for an in-lookup dentry; usually that's nothing special from ->d_compare() point of view, but... proc_sys_compare() is weird. The thing is, /proc/sys subdirectories can look differently for different processes. Up to and including having the same name resolve to different dentries - all of them hashed. The way it's done is ->d_compare() refusing to admit a match unless this dentry is supposed to be visible to this caller. The information needed to discriminate between them is stored in inode; it is set during proc_sys_lookup() and until it's done d_splice_alias() we really can't tell who should that dentry be visible for. Normally there's no negative dentries in /proc/sys; we can run into a dying dentry in RCU dcache lookup, but those can be safely rejected. However, ->d_compare() is also called for in-lookup dentries, before they get positive - or hashed, for that matter. In case of match we will wait until dentry leaves in-lookup state and repeat ->d_compare() afterwards. In other words, the right behaviour is to treat the name match as sufficient for in-lookup dentries; if dentry is not for us, we'll see that when we recheck once proc_sys_lookup() is done with it. While we are at it, fix the misspelled READ_ONCE and WRITE_ONCE there. Fixes: d9171b934526 ("parallel lookups machinery, part 4 (and last)") Reported-by: NeilBrown <[email protected]> Reviewed-by: Christian Brauner <[email protected]> Reviewed-by: NeilBrown <[email protected]> Signed-off-by: Al Viro <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Oleg Nesterov <[email protected]> Date: Sat Sep 9 18:45:01 2023 +0200 fs/proc: do_task_stat: use __for_each_thread() commit 7904e53ed5a20fc678c01d5d1b07ec486425bb6a upstream. do/while_each_thread should be avoided when possible. Link: https://lkml.kernel.org/r/[email protected] Signed-off-by: Oleg Nesterov <[email protected]> Cc: Eric W. Biederman <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Stable-dep-of: 7601df8031fd ("fs/proc: do_task_stat: use sig->stats_lock to gather the threads/children stats") Cc: [email protected] [ mheyne: adjusted context ] Signed-off-by: Maximilian Heyne <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Guillaume Nault <[email protected]> Date: Wed Jul 9 16:30:10 2025 +0200 gre: Fix IPv6 multicast route creation. commit 4e914ef063de40397e25a025c70d9737a9e45a8c upstream. Use addrconf_add_dev() instead of ipv6_find_idev() in addrconf_gre_config() so that we don't just get the inet6_dev, but also install the default ff00::/8 multicast route. Before commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address generation."), the multicast route was created at the end of the function by addrconf_add_mroute(). But this code path is now only taken in one particular case (gre devices not bound to a local IP address and in EUI64 mode). For all other cases, the function exits early and addrconf_add_mroute() is not called anymore. Using addrconf_add_dev() instead of ipv6_find_idev() in addrconf_gre_config(), fixes the problem as it will create the default multicast route for all gre devices. This also brings addrconf_gre_config() a bit closer to the normal netdevice IPv6 configuration code (addrconf_dev_config()). Cc: [email protected] Fixes: 3e6a0243ff00 ("gre: Fix again IPv6 link-local address generation.") Reported-by: Aiden Yang <[email protected]> Closes: https://lore.kernel.org/netdev/CANR=AhRM7YHHXVxJ4DmrTNMeuEOY87K2mLmo9KMed1JMr20p6g@mail.gmail.com/ Reviewed-by: Gary Guo <[email protected]> Tested-by: Gary Guo <[email protected]> Signed-off-by: Guillaume Nault <[email protected]> Reviewed-by: Ido Schimmel <[email protected]> Link: https://patch.msgid.link/027a923dcb550ad115e6d93ee8bb7d310378bd01.1752070620.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Zhang Heng <[email protected]> Date: Thu Jun 5 15:29:59 2025 +0800 HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY [ Upstream commit 1a8953f4f7746c6a515989774fe03047c522c613 ] MARTLINKTECHNOLOGY is a microphone device, when the HID interface in an audio device is requested to get specific report id, the following error may occur. [ 562.939373] usb 1-1.4.1.2: new full-speed USB device number 21 using xhci_hcd [ 563.104908] usb 1-1.4.1.2: New USB device found, idVendor=4c4a, idProduct=4155, bcdDevice= 1.00 [ 563.104910] usb 1-1.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 563.104911] usb 1-1.4.1.2: Product: USB Composite Device [ 563.104912] usb 1-1.4.1.2: Manufacturer: SmartlinkTechnology [ 563.104913] usb 1-1.4.1.2: SerialNumber: 20201111000001 [ 563.229499] input: SmartlinkTechnology USB Composite Device as /devices/pci0000:00/0000:00:07.1/0000:04:00.3/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1.2/1-1.4.1.2:1.2/0003:4C4A:4155.000F/input/input35 [ 563.291505] hid-generic 0003:4C4A:4155.000F: input,hidraw2: USB HID v2.01 Keyboard [SmartlinkTechnology USB Composite Device] on usb-0000:04:00.3-1.4.1.2/input2 [ 563.291557] usbhid 1-1.4.1.2:1.3: couldn't find an input interrupt endpoint [ 568.506654] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110) [ 573.626656] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110) [ 578.746657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110) [ 583.866655] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110) [ 588.986657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110) Ignore HID interface. The device is working properly. Signed-off-by: Zhang Heng <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Akira Inoue <[email protected]> Date: Thu Jun 12 13:34:38 2025 +0900 HID: lenovo: Add support for ThinkPad X1 Tablet Thin Keyboard Gen2 [ Upstream commit a8905238c3bbe13db90065ed74682418f23830c3 ] Add "Thinkpad X1 Tablet Gen 2 Keyboard" PID to hid-lenovo driver to fix trackpoint not working issue. Signed-off-by: Akira Inoue <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Chia-Lin Kao (AceLan) <[email protected]> Date: Tue May 6 13:50:15 2025 +0800 HID: quirks: Add quirk for 2 Chicony Electronics HP 5MP Cameras [ Upstream commit 54bae4c17c11688339eb73a04fd24203bb6e7494 ] The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C) report a HID sensor interface that is not actually implemented. Attempting to access this non-functional sensor via iio_info causes system hangs as runtime PM tries to wake up an unresponsive sensor. Add these 2 devices to the HID ignore list since the sensor interface is non-functional by design and should not be exposed to userspace. Signed-off-by: Chia-Lin Kao (AceLan) <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Jesse Brandeburg <[email protected]> Date: Fri Nov 12 17:06:02 2021 -0800 ice: safer stats processing commit 1a0f25a52e08b1f67510cabbb44888d2b3c46359 upstream. The driver was zeroing live stats that could be fetched by ndo_get_stats64 at any time. This could result in inconsistent statistics, and the telltale sign was when reading stats frequently from /proc/net/dev, the stats would go backwards. Fix by collecting stats into a local, and delaying when we write to the structure so it's not incremental. Fixes: fcea6f3da546 ("ice: Add stats and ethtool support") Signed-off-by: Jesse Brandeburg <[email protected]> Tested-by: Gurucharan G <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Closes: https://lore.kernel.org/intel-wired-lan/CAP8M2pGttT4JBjt+i4GJkxy7yERbqWJ5a8R14HzoonTLByc2Cw@mail.gmail.com Signed-off-by: Przemek Kitszel <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Hans de Goede <[email protected]> Date: Fri Jan 26 17:07:24 2024 +0100 Input: atkbd - do not skip atkbd_deactivate() when skipping ATKBD_CMD_GETID commit 9cf6e24c9fbf17e52de9fff07f12be7565ea6d61 upstream. After commit 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode") not only the getid command is skipped, but also the de-activating of the keyboard at the end of atkbd_probe(), potentially re-introducing the problem fixed by commit be2d7e4233a4 ("Input: atkbd - fix multi-byte scancode handling on reconnect"). Make sure multi-byte scancode handling on reconnect is still handled correctly by not skipping the atkbd_deactivate() call. Fixes: 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode") Tested-by: Paul Menzel <[email protected]> Signed-off-by: Hans de Goede <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Dmitry Torokhov <[email protected]> Signed-off-by: Wang Hai <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Nilton Perim Neto <[email protected]> Date: Fri Jun 27 16:29:40 2025 -0700 Input: xpad - support Acer NGR 200 Controller [ Upstream commit 22c69d786ef8fb789c61ca75492a272774221324 ] Add the NGR 200 Xbox 360 to the list of recognized controllers. Signed-off-by: Nilton Perim Neto <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: [email protected] Signed-off-by: Dmitry Torokhov <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Edward Adam Davis <[email protected]> Date: Thu Apr 11 20:05:28 2024 +0800 jfs: fix null ptr deref in dtInsertEntry commit ce6dede912f064a855acf6f04a04cbb2c25b8c8c upstream. [syzbot reported] general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] CPU: 0 PID: 5061 Comm: syz-executor404 Not tainted 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 RIP: 0010:dtInsertEntry+0xd0c/0x1780 fs/jfs/jfs_dtree.c:3713 ... [Analyze] In dtInsertEntry(), when the pointer h has the same value as p, after writing name in UniStrncpy_to_le(), p->header.flag will be cleared. This will cause the previously true judgment "p->header.flag & BT-LEAF" to change to no after writing the name operation, this leads to entering an incorrect branch and accessing the uninitialized object ih when judging this condition for the second time. [Fix] After got the page, check freelist first, if freelist == 0 then exit dtInsert() and return -EINVAL. Reported-by: [email protected] Signed-off-by: Edward Adam Davis <[email protected]> Signed-off-by: Dave Kleikamp <[email protected]> Signed-off-by: Aditya Dutt <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Al Viro <[email protected]> Date: Sun Jul 6 02:26:45 2025 +0100 ksmbd: fix a mount write count leak in ksmbd_vfs_kern_path_locked() [ Upstream commit 277627b431a0a6401635c416a21b2a0f77a77347 ] If the call of ksmbd_vfs_lock_parent() fails, we drop the parent_path references and return an error. We need to drop the write access we just got on parent_path->mnt before we drop the mount reference - callers assume that ksmbd_vfs_kern_path_locked() returns with mount write access grabbed if and only if it has returned 0. Fixes: 864fb5d37163 ("ksmbd: fix possible deadlock in smb2_open") Signed-off-by: Al Viro <[email protected]> Acked-by: Namjae Jeon <[email protected]> Signed-off-by: Steve French <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Greg Kroah-Hartman <[email protected]> Date: Thu Jul 17 18:30:55 2025 +0200 Linux 5.15.189 Link: https://lore.kernel.org/r/[email protected] Tested-by: Vijayendra Suman <[email protected]> Tested-by: Shuah Khan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Tested-by: Jon Hunter <[email protected]> Tested-by: Mark Brown <[email protected]> Tested-by: Ron Economos <[email protected]> Tested-by: Florian Fainelli <[email protected]> Tested-by: Linux Kernel Functional Testing <[email protected]> Tested-by: Brett A C Sheffield <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Wang Jinchao <[email protected]> Date: Thu Jun 12 19:28:40 2025 +0800 md/raid1: Fix stack memory use after return in raid1_reshape [ Upstream commit d67ed2ccd2d1dcfda9292c0ea8697a9d0f2f0d98 ] In the raid1_reshape function, newpool is allocated on the stack and assigned to conf->r1bio_pool. This results in conf->r1bio_pool.wait.head pointing to a stack address. Accessing this address later can lead to a kernel panic. Example access path: raid1_reshape() { // newpool is on the stack mempool_t newpool, oldpool; // initialize newpool.wait.head to stack address mempool_init(&newpool, ...); conf->r1bio_pool = newpool; } raid1_read_request() or raid1_write_request() { alloc_r1bio() { mempool_alloc() { // if pool->alloc fails remove_element() { --pool->curr_nr; } } } } mempool_free() { if (pool->curr_nr < pool->min_nr) { // pool->wait.head is a stack address // wake_up() will try to access this invalid address // which leads to a kernel panic return; wake_up(&pool->wait); } } Fix: reinit conf->r1bio_pool.wait after assigning newpool. Fixes: afeee514ce7f ("md: convert to bioset_init()/mempool_init()") Signed-off-by: Wang Jinchao <[email protected]> Reviewed-by: Yu Kuai <[email protected]> Link: https://lore.kernel.org/linux-raid/[email protected] Signed-off-by: Yu Kuai <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Zheng Qixing <[email protected]> Date: Thu Jun 12 21:24:05 2025 +0800 nbd: fix uaf in nbd_genl_connect() error path [ Upstream commit aa9552438ebf015fc5f9f890dbfe39f0c53cf37e ] There is a use-after-free issue in nbd: block nbd6: Receive control failed (result -104) block nbd6: shutting down sockets ================================================================== BUG: KASAN: slab-use-after-free in recv_work+0x694/0xa80 drivers/block/nbd.c:1022 Write of size 4 at addr ffff8880295de478 by task kworker/u33:0/67 CPU: 2 UID: 0 PID: 67 Comm: kworker/u33:0 Not tainted 6.15.0-rc5-syzkaller-00123-g2c89c1b655c0 #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Workqueue: nbd6-recv recv_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189 instrument_atomic_read_write include/linux/instrumented.h:96 [inline] atomic_dec include/linux/atomic/atomic-instrumented.h:592 [inline] recv_work+0x694/0xa80 drivers/block/nbd.c:1022 process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400 kthread+0x3c2/0x780 kernel/kthread.c:464 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> nbd_genl_connect() does not properly stop the device on certain error paths after nbd_start_device() has been called. This causes the error path to put nbd->config while recv_work continue to use the config after putting it, leading to use-after-free in recv_work. This patch moves nbd_start_device() after the backend file creation. Reported-by: [email protected] Closes: https://lore.kernel.org/all/[email protected]/T/ Fixes: 6497ef8df568 ("nbd: provide a way for userspace processes to identify device backends") Signed-off-by: Zheng Qixing <[email protected]> Reviewed-by: Yu Kuai <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Victor Nogueira <[email protected]> Date: Mon Jul 7 18:08:01 2025 -0300 net/sched: Abort __tc_modify_qdisc if parent class does not exist [ Upstream commit ffdde7bf5a439aaa1955ebd581f5c64ab1533963 ] Lion's patch [1] revealed an ancient bug in the qdisc API. Whenever a user creates/modifies a qdisc specifying as a parent another qdisc, the qdisc API will, during grafting, detect that the user is not trying to attach to a class and reject. However grafting is performed after qdisc_create (and thus the qdiscs' init callback) is executed. In qdiscs that eventually call qdisc_tree_reduce_backlog during init or change (such as fq, hhf, choke, etc), an issue arises. For example, executing the following commands: sudo tc qdisc add dev lo root handle a: htb default 2 sudo tc qdisc add dev lo parent a: handle beef fq Qdiscs such as fq, hhf, choke, etc unconditionally invoke qdisc_tree_reduce_backlog() in their control path init() or change() which then causes a failure to find the child class; however, that does not stop the unconditional invocation of the assumed child qdisc's qlen_notify with a null class. All these qdiscs make the assumption that class is non-null. The solution is ensure that qdisc_leaf() which looks up the parent class, and is invoked prior to qdisc_create(), should return failure on not finding the class. In this patch, we leverage qdisc_leaf to return ERR_PTRs whenever the parentid doesn't correspond to a class, so that we can detect it earlier on and abort before qdisc_create is called. [1] https://lore.kernel.org/netdev/[email protected]/ Fixes: 5e50da01d0ce ("[NET_SCHED]: Fix endless loops (part 2): "simple" qdiscs") Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/ Acked-by: Jamal Hadi Salim <[email protected]> Reviewed-by: Cong Wang <[email protected]> Signed-off-by: Victor Nogueira <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kito Xu <[email protected]> Date: Wed Jul 9 03:52:51 2025 +0000 net: appletalk: Fix device refcount leak in atrtr_create() [ Upstream commit 711c80f7d8b163d3ecd463cd96f07230f488e750 ] When updating an existing route entry in atrtr_create(), the old device reference was not being released before assigning the new device, leading to a device refcount leak. Fix this by calling dev_put() to release the old device reference before holding the new one. Fixes: c7f905f0f6d4 ("[ATALK]: Add missing dev_hold() to atrtr_create().") Signed-off-by: Kito Xu <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Alok Tiwari <[email protected]> Date: Thu Jul 10 11:06:17 2025 -0700 net: ll_temac: Fix missing tx_pending check in ethtools_set_ringparam() [ Upstream commit e81750b4e3826fedce7362dad839cb40384d60ae ] The function ll_temac_ethtools_set_ringparam() incorrectly checked rx_pending twice, once correctly for RX and once mistakenly in place of tx_pending. This caused tx_pending to be left unchecked against TX_BD_NUM_MAX. As a result, invalid TX ring sizes may have been accepted or valid ones wrongly rejected based on the RX limit, leading to potential misconfiguration or unexpected results. This patch corrects the condition to properly validate tx_pending. Fixes: f7b261bfc35e ("net: ll_temac: Make RX/TX ring sizes configurable") Signed-off-by: Alok Tiwari <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Oleksij Rempel <[email protected]> Date: Wed Jul 9 15:07:53 2025 +0200 net: phy: microchip: limit 100M workaround to link-down events on LAN88xx [ Upstream commit dd4360c0e8504f2f7639c7f5d07c93cfd6a98333 ] Restrict the 100Mbit forced-mode workaround to link-down transitions only, to prevent repeated link reset cycles in certain configurations. The workaround was originally introduced to improve signal reliability when switching cables between long and short distances. It temporarily forces the PHY into 10 Mbps before returning to 100 Mbps. However, when used with autonegotiating link partners (e.g., Intel i350), executing this workaround on every link change can confuse the partner and cause constant renegotiation loops. This results in repeated link down/up transitions and the PHY never reaching a stable state. Limit the workaround to only run during the PHY_NOLINK state. This ensures it is triggered only once per link drop, avoiding disruptive toggling while still preserving its intended effect. Note: I am not able to reproduce the original issue that this workaround addresses. I can only confirm that 100 Mbit mode works correctly in my test setup. Based on code inspection, I assume the workaround aims to reset some internal state machine or signal block by toggling speeds. However, a PHY reset is already performed earlier in the function via phy_init_hw(), which may achieve a similar effect. Without a reproducer, I conservatively keep the workaround but restrict its conditions. Fixes: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver") Signed-off-by: Oleksij Rempel <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Oleksij Rempel <[email protected]> Date: Thu Jul 3 13:49:39 2025 +0200 net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap [ Upstream commit a141af8eb2272ab0f677a7f2653874840bc9b214 ] Correct the Auto-MDIX configuration to ensure userspace settings are respected when the feature is disabled by the AUTOMDIX_EN hardware strap. The LAN9500 PHY allows its default MDI-X mode to be configured via a hardware strap. If this strap sets the default to "MDI-X off", the driver was previously unable to enable Auto-MDIX from userspace. When handling the ETH_TP_MDI_AUTO case, the driver would set the SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY falls back to its hardware strap default, ignoring the software request. This patch corrects the behavior by also setting the override bit when enabling Auto-MDIX. This ensures that the userspace configuration takes precedence over the hardware strap, allowing Auto-MDIX to be enabled correctly in all scenarios. Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <[email protected]> Cc: Andre Edich <[email protected]> Reviewed-by: Maxime Chevallier <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Oleksij Rempel <[email protected]> Date: Thu Jul 3 13:49:41 2025 +0200 net: phy: smsc: Fix link failure in forced mode with Auto-MDIX [ Upstream commit 9dfe110cc0f6ef42af8e81ce52aef34a647d0b8a ] Force a fixed MDI-X mode when auto-negotiation is disabled to prevent link instability. When forcing the link speed and duplex on a LAN9500 PHY (e.g., with `ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto mode, the PHY fails to establish a stable link. This occurs because the PHY's Auto-MDIX algorithm is not designed to operate when auto-negotiation is disabled. In this state, the PHY continuously toggles the TX/RX signal pairs, which prevents the link partner from synchronizing. This patch resolves the issue by detecting when auto-negotiation is disabled. If the MDI-X control mode is set to 'auto', the driver now forces a specific, stable mode (ETH_TP_MDI) to prevent the pair toggling. This choice of a fixed MDI mode mirrors the behavior the hardware would exhibit if the AUTOMDIX_EN strap were configured for a fixed MDI connection. Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <[email protected]> Cc: Andre Edich <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Xiaowei Li <[email protected]> Date: Fri Jun 20 10:27:02 2025 +0800 net: usb: qmi_wwan: add SIMCom 8230C composition [ Upstream commit 0b39b055b5b48cbbdf5746a1ca6e3f6b0221e537 ] Add support for SIMCom 8230C which is based on Qualcomm SDX35 chip. 0x9071: tty (DM) + tty (NMEA) + tty (AT) + rmnet T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9071 Rev= 5.15 S: Manufacturer=SIMCOM S: Product=SDXBAAGHA-IDP _SN:D744C4C5 S: SerialNumber=0123456789ABCDEF C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=none E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Xiaowei Li <[email protected]> Acked-by: Bjørn Mork <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Eric Dumazet <[email protected]> Date: Mon Jul 7 12:45:17 2025 +0000 netfilter: flowtable: account for Ethernet header in nf_flow_pppoe_proto() [ Upstream commit 18cdb3d982da8976b28d57691eb256ec5688fad2 ] syzbot found a potential access to uninit-value in nf_flow_pppoe_proto() Blamed commit forgot the Ethernet header. BUG: KMSAN: uninit-value in nf_flow_offload_inet_hook+0x7e4/0x940 net/netfilter/nf_flow_table_inet.c:27 nf_flow_offload_inet_hook+0x7e4/0x940 net/netfilter/nf_flow_table_inet.c:27 nf_hook_entry_hookfn include/linux/netfilter.h:157 [inline] nf_hook_slow+0xe1/0x3d0 net/netfilter/core.c:623 nf_hook_ingress include/linux/netfilter_netdev.h:34 [inline] nf_ingress net/core/dev.c:5742 [inline] __netif_receive_skb_core+0x4aff/0x70c0 net/core/dev.c:5837 __netif_receive_skb_one_core net/core/dev.c:5975 [inline] __netif_receive_skb+0xcc/0xac0 net/core/dev.c:6090 netif_receive_skb_internal net/core/dev.c:6176 [inline] netif_receive_skb+0x57/0x630 net/core/dev.c:6235 tun_rx_batched+0x1df/0x980 drivers/net/tun.c:1485 tun_get_user+0x4ee0/0x6b40 drivers/net/tun.c:1938 tun_chr_write_iter+0x3e9/0x5c0 drivers/net/tun.c:1984 new_sync_write fs/read_write.c:593 [inline] vfs_write+0xb4b/0x1580 fs/read_write.c:686 ksys_write fs/read_write.c:738 [inline] __do_sys_write fs/read_write.c:749 [inline] Reported-by: [email protected] Closes: https://lore.kernel.org/netdev/[email protected]/T/#u Fixes: 87b3593bed18 ("netfilter: flowtable: validate pppoe header") Signed-off-by: Eric Dumazet <[email protected]> Reviewed-by: Pablo Neira Ayuso <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Fri Jul 11 05:32:07 2025 +0000 netlink: Fix rmem check in netlink_broadcast_deliver(). commit a3c4a125ec725cefb40047eb05ff9eafd57830b4 upstream. We need to allow queuing at least one skb even when skb is larger than sk->sk_rcvbuf. The cited commit made a mistake while converting a condition in netlink_broadcast_deliver(). Let's correct the rmem check for the allow-one-skb rule. Fixes: ae8f160e7eb24 ("netlink: Fix wraparounds of sk->sk_rmem_alloc.") Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Fri Jul 4 05:48:18 2025 +0000 netlink: Fix wraparounds of sk->sk_rmem_alloc. [ Upstream commit ae8f160e7eb24240a2a79fc4c815c6a0d4ee16cc ] Netlink has this pattern in some places if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf) atomic_add(skb->truesize, &sk->sk_rmem_alloc); , which has the same problem fixed by commit 5a465a0da13e ("udp: Fix multiple wraparounds of sk->sk_rmem_alloc."). For example, if we set INT_MAX to SO_RCVBUFFORCE, the condition is always false as the two operands are of int. Then, a single socket can eat as many skb as possible until OOM happens, and we can see multiple wraparounds of sk->sk_rmem_alloc. Let's fix it by using atomic_add_return() and comparing the two variables as unsigned int. Before: [root@fedora ~]# ss -f netlink Recv-Q Send-Q Local Address:Port Peer Address:Port -1668710080 0 rtnl:nl_wraparound/293 * After: [root@fedora ~]# ss -f netlink Recv-Q Send-Q Local Address:Port Peer Address:Port 2147483072 0 rtnl:nl_wraparound/290 * ^ `--- INT_MAX - 576 Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Jason Baron <[email protected]> Closes: https://lore.kernel.org/netdev/[email protected]/ Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Jakub Kicinski <[email protected]> Date: Thu Jul 10 17:11:21 2025 -0700 netlink: make sure we allow at least one dump skb commit a215b5723922f8099078478122f02100e489cb80 upstream. Commit under Fixes tightened up the memory accounting for Netlink sockets. Looks like the accounting is too strict for some existing use cases, Marek reported issues with nl80211 / WiFi iw CLI. To reduce number of iterations Netlink dumps try to allocate messages based on the size of the buffer passed to previous recvmsg() calls. If user space uses a larger buffer in recvmsg() than sk_rcvbuf we will allocate an skb we won't be able to queue. Make sure we always allow at least one skb to be queued. Same workaround is already present in netlink_attachskb(). Alternative would be to cap the allocation size to rcvbuf - rmem_alloc but as I said, the workaround is already present in other places. Reported-by: Marek Szyprowski <[email protected]> Link: https://lore.kernel.org/[email protected] Fixes: ae8f160e7eb2 ("netlink: Fix wraparounds of sk->sk_rmem_alloc.") Tested-by: Marek Szyprowski <[email protected]> Reviewed-by: Kuniyuki Iwashima <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Peter Zijlstra <[email protected]> Date: Wed Jul 2 18:21:44 2025 +0200 perf: Revert to requiring CAP_SYS_ADMIN for uprobes [ Upstream commit ba677dbe77af5ffe6204e0f3f547f3ba059c6302 ] Jann reports that uprobes can be used destructively when used in the middle of an instruction. The kernel only verifies there is a valid instruction at the requested offset, but due to variable instruction length cannot determine if this is an instruction as seen by the intended execution stream. Additionally, Mark Rutland notes that on architectures that mix data in the text segment (like arm64), a similar things can be done if the data word is 'mistaken' for an instruction. As such, require CAP_SYS_ADMIN for uprobes. Fixes: c9e0924e5c2b ("perf/core: open access to probes for CAP_PERFMON privileged process") Reported-by: Jann Horn <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Link: https://lkml.kernel.org/r/CAG48ez1n4520sq0XrWYDHKiKxE_+WCfAK+qt9qkY4ZiBGmL-5g@mail.gmail.com Signed-off-by: Sasha Levin <[email protected]>
Author: Bartosz Golaszewski <[email protected]> Date: Thu Jun 12 11:14:48 2025 +0200 pinctrl: qcom: msm: mark certain pins as invalid for interrupts commit 93712205ce2f1fb047739494c0399a26ea4f0890 upstream. On some platforms, the UFS-reset pin has no interrupt logic in TLMM but is nevertheless registered as a GPIO in the kernel. This enables the user-space to trigger a BUG() in the pinctrl-msm driver by running, for example: `gpiomon -c 0 113` on RB2. The exact culprit is requesting pins whose intr_detection_width setting is not 1 or 2 for interrupts. This hits a BUG() in msm_gpio_irq_set_type(). Potentially crashing the kernel due to an invalid request from user-space is not optimal, so let's go through the pins and mark those that would fail the check as invalid for the irq chip as we should not even register them as available irqs. This function can be extended if we determine that there are more corner-cases like this. Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver") Cc: [email protected] Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Bartosz Golaszewski <[email protected]> Link: https://lore.kernel.org/[email protected] Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Uwe Kleine-König <[email protected]> Date: Fri Jul 4 19:27:27 2025 +0200 pwm: mediatek: Ensure to disable clocks in error path commit 505b730ede7f5c4083ff212aa955155b5b92e574 upstream. After enabling the clocks each error path must disable the clocks again. One of them failed to do so. Unify the error paths to use goto to make it harder for future changes to add a similar bug. Fixes: 7ca59947b5fc ("pwm: mediatek: Prevent divide-by-zero in pwm_mediatek_config()") Signed-off-by: Uwe Kleine-König <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: [email protected] [ukleinek: backported to 5.15.y] Signed-off-by: Uwe Kleine-König <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Nigel Croxon <[email protected]> Date: Thu Jul 3 11:23:04 2025 -0400 raid10: cleanup memleak at raid10_make_request [ Upstream commit 43806c3d5b9bb7d74ba4e33a6a8a41ac988bde24 ] If raid10_read_request or raid10_write_request registers a new request and the REQ_NOWAIT flag is set, the code does not free the malloc from the mempool. unreferenced object 0xffff8884802c3200 (size 192): comm "fio", pid 9197, jiffies 4298078271 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 88 41 02 00 00 00 00 00 .........A...... 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc c1a049a2): __kmalloc+0x2bb/0x450 mempool_alloc+0x11b/0x320 raid10_make_request+0x19e/0x650 [raid10] md_handle_request+0x3b3/0x9e0 __submit_bio+0x394/0x560 __submit_bio_noacct+0x145/0x530 submit_bio_noacct_nocheck+0x682/0x830 __blkdev_direct_IO_async+0x4dc/0x6b0 blkdev_read_iter+0x1e5/0x3b0 __io_read+0x230/0x1110 io_read+0x13/0x30 io_issue_sqe+0x134/0x1180 io_submit_sqes+0x48c/0xe90 __do_sys_io_uring_enter+0x574/0x8b0 do_syscall_64+0x5c/0xe0 entry_SYSCALL_64_after_hwframe+0x76/0x7e V4: changing backing tree to see if CKI tests will pass. The patch code has not changed between any versions. Fixes: c9aa889b035f ("md: raid10 add nowait support") Signed-off-by: Nigel Croxon <[email protected]> Link: https://lore.kernel.org/linux-raid/[email protected] Signed-off-by: Yu Kuai <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Patrisious Haddad <[email protected]> Date: Mon Jun 16 12:14:54 2025 +0300 RDMA/mlx5: Fix vport loopback for MPV device [ Upstream commit a9a9e68954f29b1e197663f76289db4879fd51bb ] Always enable vport loopback for both MPV devices on driver start. Previously in some cases related to MPV RoCE, packets weren't correctly executing loopback check at vport in FW, since it was disabled. Due to complexity of identifying such cases for MPV always enable vport loopback for both GVMIs when binding the slave to the master port. Fixes: 0042f9e458a5 ("RDMA/mlx5: Enable vport loopback when user context or QP mandate") Signed-off-by: Patrisious Haddad <[email protected]> Reviewed-by: Mark Bloch <[email protected]> Link: https://patch.msgid.link/d4298f5ebb2197459e9e7221c51ecd6a34699847.1750064969.git.leon@kernel.org Signed-off-by: Leon Romanovsky <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Rafael J. Wysocki <[email protected]> Date: Thu Jul 3 12:54:55 2025 +0200 Revert "ACPI: battery: negate current when discharging" commit de1675de39aa945bad5937d1fde4df3682670639 upstream. Revert commit 234f71555019 ("ACPI: battery: negate current when discharging") breaks not one but several userspace implementations of battery monitoring: Steam and MangoHud. Perhaps it breaks more, but those are the two that have been tested. Reported-by: Matthew Schwartz <[email protected]> Closes: https://lore.kernel.org/linux-acpi/[email protected]/ Signed-off-by: Rafael J. Wysocki <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Michael Jeanson <[email protected]> Date: Thu Mar 6 16:12:21 2025 -0500 rseq: Fix segfault on registration when rseq_cs is non-zero commit fd881d0a085fc54354414aed990ccf05f282ba53 upstream. The rseq_cs field is documented as being set to 0 by user-space prior to registration, however this is not currently enforced by the kernel. This can result in a segfault on return to user-space if the value stored in the rseq_cs field doesn't point to a valid struct rseq_cs. The correct solution to this would be to fail the rseq registration when the rseq_cs field is non-zero. However, some older versions of glibc will reuse the rseq area of previous threads without clearing the rseq_cs field and will also terminate the process if the rseq registration fails in a secondary thread. This wasn't caught in testing because in this case the leftover rseq_cs does point to a valid struct rseq_cs. What we can do is clear the rseq_cs field on registration when it's non-zero which will prevent segfaults on registration and won't break the glibc versions that reuse rseq areas on thread creation. Signed-off-by: Michael Jeanson <[email protected]> Signed-off-by: Ingo Molnar <[email protected]> Reviewed-by: Mathieu Desnoyers <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Linus Torvalds <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: David Howells <[email protected]> Date: Tue Jul 8 22:15:04 2025 +0100 rxrpc: Fix oops due to non-existence of prealloc backlog struct commit 880a88f318cf1d2a0f4c0a7ff7b07e2062b434a4 upstream. If an AF_RXRPC service socket is opened and bound, but calls are preallocated, then rxrpc_alloc_incoming_call() will oops because the rxrpc_backlog struct doesn't get allocated until the first preallocation is made. Fix this by returning NULL from rxrpc_alloc_incoming_call() if there is no backlog struct. This will cause the incoming call to be aborted. Reported-by: Junvyyang, Tencent Zhuque Lab <[email protected]> Suggested-by: Junvyyang, Tencent Zhuque Lab <[email protected]> Signed-off-by: David Howells <[email protected]> cc: LePremierHomme <[email protected]> cc: Marc Dionne <[email protected]> cc: Willy Tarreau <[email protected]> cc: Simon Horman <[email protected]> cc: [email protected] Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Stefan Metzmacher <[email protected]> Date: Wed Jul 2 09:18:05 2025 +0200 smb: server: make use of rdma_destroy_qp() [ Upstream commit 0c2b53997e8f5e2ec9e0fbd17ac0436466b65488 ] The qp is created by rdma_create_qp() as t->cm_id->qp and t->qp is just a shortcut. rdma_destroy_qp() also calls ib_destroy_qp(cm_id->qp) internally, but it is protected by a mutex, clears the cm_id and also calls trace_cm_qp_destroy(). This should make the tracing more useful as both rdma_create_qp() and rdma_destroy_qp() are traces and it makes the code look more sane as functions from the same layer are used for the specific qp object. trace-cmd stream -e rdma_cma:cm_qp_create -e rdma_cma:cm_qp_destroy shows this now while doing a mount and unmount from a client: <...>-80 [002] 378.514182: cm_qp_create: cm.id=1 src=172.31.9.167:5445 dst=172.31.9.166:37113 tos=0 pd.id=0 qp_type=RC send_wr=867 recv_wr=255 qp_num=1 rc=0 <...>-6283 [001] 381.686172: cm_qp_destroy: cm.id=1 src=172.31.9.167:5445 dst=172.31.9.166:37113 tos=0 qp_num=1 Before we only saw the first line. Cc: Namjae Jeon <[email protected]> Cc: Steve French <[email protected]> Cc: Sergey Senozhatsky <[email protected]> Cc: Hyunchul Lee <[email protected]> Cc: Tom Talpey <[email protected]> Cc: [email protected] Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <[email protected]> Reviewed-by: Tom Talpey <[email protected]> Acked-by: Namjae Jeon <[email protected]> Signed-off-by: Steve French <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Lee, Chun-Yi <[email protected]> Date: Mon Aug 8 21:21:58 2022 +0800 thermal/int340x_thermal: handle data_vault when the value is ZERO_SIZE_PTR commit 7931e28098a4c1a2a6802510b0cbe57546d2049d upstream. In some case, the GDDV returns a package with a buffer which has zero length. It causes that kmemdup() returns ZERO_SIZE_PTR (0x10). Then the data_vault_read() got NULL point dereference problem when accessing the 0x10 value in data_vault. [ 71.024560] BUG: kernel NULL pointer dereference, address: 0000000000000010 This patch uses ZERO_OR_NULL_PTR() for checking ZERO_SIZE_PTR or NULL value in data_vault. Signed-off-by: "Lee, Chun-Yi" <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]> [ Larry: backport to 5.15.y. Minor conflict resolved due to missing commit 9e5d3d6be664 thermal: int340x: Consolidate freeing of acpi_buffer pointer ] Signed-off-by: Larry Bassel <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Kuniyuki Iwashima <[email protected]> Date: Wed Jul 2 01:43:40 2025 +0000 tipc: Fix use-after-free in tipc_conn_close(). [ Upstream commit 667eeab4999e981c96b447a4df5f20bdf5c26f13 ] syzbot reported a null-ptr-deref in tipc_conn_close() during netns dismantle. [0] tipc_topsrv_stop() iterates tipc_net(net)->topsrv->conn_idr and calls tipc_conn_close() for each tipc_conn. The problem is that tipc_conn_close() is called after releasing the IDR lock. At the same time, there might be tipc_conn_recv_work() running and it could call tipc_conn_close() for the same tipc_conn and release its last ->kref. Once we release the IDR lock in tipc_topsrv_stop(), there is no guarantee that the tipc_conn is alive. Let's hold the ref before releasing the lock and put the ref after tipc_conn_close() in tipc_topsrv_stop(). [0]: BUG: KASAN: use-after-free in tipc_conn_close+0x122/0x140 net/tipc/topsrv.c:165 Read of size 8 at addr ffff888099305a08 by task kworker/u4:3/435 CPU: 0 PID: 435 Comm: kworker/u4:3 Not tainted 4.19.204-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: netns cleanup_net Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1fc/0x2ef lib/dump_stack.c:118 print_address_description.cold+0x54/0x219 mm/kasan/report.c:256 kasan_report_error.cold+0x8a/0x1b9 mm/kasan/report.c:354 kasan_report mm/kasan/report.c:412 [inline] __asan_report_load8_noabort+0x88/0x90 mm/kasan/report.c:433 tipc_conn_close+0x122/0x140 net/tipc/topsrv.c:165 tipc_topsrv_stop net/tipc/topsrv.c:701 [inline] tipc_topsrv_exit_net+0x27b/0x5c0 net/tipc/topsrv.c:722 ops_exit_list+0xa5/0x150 net/core/net_namespace.c:153 cleanup_net+0x3b4/0x8b0 net/core/net_namespace.c:553 process_one_work+0x864/0x1570 kernel/workqueue.c:2153 worker_thread+0x64c/0x1130 kernel/workqueue.c:2296 kthread+0x33f/0x460 kernel/kthread.c:259 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415 Allocated by task 23: kmem_cache_alloc_trace+0x12f/0x380 mm/slab.c:3625 kmalloc include/linux/slab.h:515 [inline] kzalloc include/linux/slab.h:709 [inline] tipc_conn_alloc+0x43/0x4f0 net/tipc/topsrv.c:192 tipc_topsrv_accept+0x1b5/0x280 net/tipc/topsrv.c:470 process_one_work+0x864/0x1570 kernel/workqueue.c:2153 worker_thread+0x64c/0x1130 kernel/workqueue.c:2296 kthread+0x33f/0x460 kernel/kthread.c:259 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415 Freed by task 23: __cache_free mm/slab.c:3503 [inline] kfree+0xcc/0x210 mm/slab.c:3822 tipc_conn_kref_release net/tipc/topsrv.c:150 [inline] kref_put include/linux/kref.h:70 [inline] conn_put+0x2cd/0x3a0 net/tipc/topsrv.c:155 process_one_work+0x864/0x1570 kernel/workqueue.c:2153 worker_thread+0x64c/0x1130 kernel/workqueue.c:2296 kthread+0x33f/0x460 kernel/kthread.c:259 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415 The buggy address belongs to the object at ffff888099305a00 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 8 bytes inside of 512-byte region [ffff888099305a00, ffff888099305c00) The buggy address belongs to the page: page:ffffea000264c140 count:1 mapcount:0 mapping:ffff88813bff0940 index:0x0 flags: 0xfff00000000100(slab) raw: 00fff00000000100 ffffea00028b6b88 ffffea0002cd2b08 ffff88813bff0940 raw: 0000000000000000 ffff888099305000 0000000100000006 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888099305900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888099305980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff888099305a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888099305a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888099305b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: c5fa7b3cf3cb ("tipc: introduce new TIPC server infrastructure") Reported-by: [email protected] Closes: https://syzkaller.appspot.com/bug?extid=27169a847a70550d17be Signed-off-by: Kuniyuki Iwashima <[email protected]> Reviewed-by: Tung Nguyen <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Tiwei Bie <[email protected]> Date: Mon Jun 23 19:08:29 2025 +0800 um: vector: Reduce stack usage in vector_eth_configure() [ Upstream commit 2d65fc13be85c336c56af7077f08ccd3a3a15a4a ] When compiling with clang (19.1.7), initializing *vp using a compound literal may result in excessive stack usage. Fix it by initializing the required fields of *vp individually. Without this patch: $ objdump -d arch/um/drivers/vector_kern.o | ./scripts/checkstack.pl x86_64 0 ... 0x0000000000000540 vector_eth_configure [vector_kern.o]:1472 ... With this patch: $ objdump -d arch/um/drivers/vector_kern.o | ./scripts/checkstack.pl x86_64 0 ... 0x0000000000000540 vector_eth_configure [vector_kern.o]:208 ... Reported-by: kernel test robot <[email protected]> Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/ Signed-off-by: Tiwei Bie <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Pawel Laszczak <[email protected]> Date: Fri Jun 20 08:23:12 2025 +0000 usb: cdnsp: Fix issue with CV Bad Descriptor test [ Upstream commit 2831a81077f5162f104ba5a97a7d886eb371c21c ] The SSP2 controller has extra endpoint state preserve bit (ESP) which setting causes that endpoint state will be preserved during Halt Endpoint command. It is used only for EP0. Without this bit the Command Verifier "TD 9.10 Bad Descriptor Test" failed. Setting this bit doesn't have any impact for SSP controller. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Cc: stable <[email protected]> Signed-off-by: Pawel Laszczak <[email protected]> Acked-by: Peter Chen <[email protected]> Link: https://lore.kernel.org/r/PH7PR07MB95382CCD50549DABAEFD6156DD7CA@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Lee Jones <[email protected]> Date: Thu Nov 30 10:54:36 2023 +0000 usb: cdnsp: Replace snprintf() with the safer scnprintf() variant [ Upstream commit b385ef088c7aab20a2c0dc20d390d69a6620f0f3 ] There is a general misunderstanding amongst engineers that {v}snprintf() returns the length of the data *actually* encoded into the destination array. However, as per the C99 standard {v}snprintf() really returns the length of the data that *would have been* written if there were enough space for it. This misunderstanding has led to buffer-overruns in the past. It's generally considered safer to use the {v}scnprintf() variants in their place (or even sprintf() in simple cases). So let's do that. The uses in this file all seem to assume that data *has been* written! Link: https://lwn.net/Articles/69419/ Link: https://github.com/KSPP/linux/issues/105 Cc: Pawel Laszczak <[email protected]> Cc: Greg Kroah-Hartman <[email protected]> Cc: [email protected] Signed-off-by: Lee Jones <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Stable-dep-of: 2831a81077f5 ("usb: cdnsp: Fix issue with CV Bad Descriptor test") Signed-off-by: Sasha Levin <[email protected]>
Author: Kuen-Han Tsai <[email protected]> Date: Wed May 28 18:03:11 2025 +0800 usb: dwc3: Abort suspend on soft disconnect failure [ Upstream commit 630a1dec3b0eba2a695b9063f1c205d585cbfec9 ] When dwc3_gadget_soft_disconnect() fails, dwc3_suspend_common() keeps going with the suspend, resulting in a period where the power domain is off, but the gadget driver remains connected. Within this time frame, invoking vbus_event_work() will cause an error as it attempts to access DWC3 registers for endpoint disabling after the power domain has been completely shut down. Abort the suspend sequence when dwc3_gadget_suspend() cannot halt the controller and proceeds with a soft connect. Fixes: 9f8a67b65a49 ("usb: dwc3: gadget: fix gadget suspend/resume") Cc: stable <[email protected]> Acked-by: Thinh Nguyen <[email protected]> Signed-off-by: Kuen-Han Tsai <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Kuen-Han Tsai <[email protected]> Date: Tue Jun 17 13:07:12 2025 +0800 usb: gadget: u_serial: Fix race condition in TTY wakeup commit c529c3730bd09115684644e26bf01ecbd7e2c2c9 upstream. A race condition occurs when gs_start_io() calls either gs_start_rx() or gs_start_tx(), as those functions briefly drop the port_lock for usb_ep_queue(). This allows gs_close() and gserial_disconnect() to clear port.tty and port_usb, respectively. Use the null-safe TTY Port helper function to wake up TTY. Example CPU1: CPU2: gserial_connect() // lock gs_close() // await lock gs_start_rx() // unlock usb_ep_queue() gs_close() // lock, reset port.tty and unlock gs_start_rx() // lock tty_wakeup() // NPE Fixes: 35f95fd7f234 ("TTY: usb/u_serial, use tty from tty_port") Cc: stable <[email protected]> Signed-off-by: Kuen-Han Tsai <[email protected]> Reviewed-by: Prashanth K <[email protected]> Link: https://lore.kernel.org/linux-usb/[email protected]/ Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Raju Rangoju <[email protected]> Date: Fri Jun 27 17:41:19 2025 +0300 usb: xhci: quirk for data loss in ISOC transfers [ Upstream commit cbc889ab0122366f6cdbe3c28d477c683ebcebc2 ] During the High-Speed Isochronous Audio transfers, xHCI controller on certain AMD platforms experiences momentary data loss. This results in Missed Service Errors (MSE) being generated by the xHCI. The root cause of the MSE is attributed to the ISOC OUT endpoint being omitted from scheduling. This can happen when an IN endpoint with a 64ms service interval either is pre-scheduled prior to the ISOC OUT endpoint or the interval of the ISOC OUT endpoint is shorter than that of the IN endpoint. Consequently, the OUT service is neglected when an IN endpoint with a service interval exceeding 32ms is scheduled concurrently (every 64ms in this scenario). This issue is particularly seen on certain older AMD platforms. To mitigate this problem, it is recommended to adjust the service interval of the IN endpoint to not exceed 32ms (interval 8). This adjustment ensures that the OUT endpoint will not be bypassed, even if a smaller interval value is utilized. Cc: stable <[email protected]> Signed-off-by: Raju Rangoju <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Pawel Laszczak <[email protected]> Date: Thu Oct 26 09:37:37 2023 +0200 usb:cdnsp: remove TRB_FLUSH_ENDPOINT command [ Upstream commit 2998874736bca1031ca84b0a3235a2cd09dfa426 ] Patch removes TRB_FLUSH_ENDPOINT command from driver. This command is not supported by controller and USBSSP returns TRB Error completion code for it. Signed-off-by: Pawel Laszczak <[email protected]> Acked-by: Peter Chen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Stable-dep-of: 2831a81077f5 ("usb: cdnsp: Fix issue with CV Bad Descriptor test") Signed-off-by: Sasha Levin <[email protected]>
Author: Dongli Zhang <[email protected]> Date: Wed Apr 2 23:29:46 2025 -0700 vhost-scsi: protect vq->log_used with vq->mutex commit f591cf9fce724e5075cc67488c43c6e39e8cbe27 upstream. The vhost-scsi completion path may access vq->log_base when vq->log_used is already set to false. vhost-thread QEMU-thread vhost_scsi_complete_cmd_work() -> vhost_add_used() -> vhost_add_used_n() if (unlikely(vq->log_used)) QEMU disables vq->log_used via VHOST_SET_VRING_ADDR. mutex_lock(&vq->mutex); vq->log_used = false now! mutex_unlock(&vq->mutex); QEMU gfree(vq->log_base) log_used() -> log_write(vq->log_base) Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be reclaimed via gfree(). As a result, this causes invalid memory writes to QEMU userspace. The control queue path has the same issue. Signed-off-by: Dongli Zhang <[email protected]> Acked-by: Jason Wang <[email protected]> Reviewed-by: Mike Christie <[email protected]> Message-Id: <[email protected]> Signed-off-by: Michael S. Tsirkin <[email protected]> [ Resolved conflicts in drivers/vhost/scsi.c bacause vhost_scsi_complete_cmd_work() has been refactored. ] Signed-off-by: Xinyu Zheng <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Bui Quang Minh <[email protected]> Date: Fri Jul 11 23:52:02 2025 -0400 virtio-net: ensure the received length does not exceed allocated size [ Upstream commit 315dbdd7cdf6aa533829774caaf4d25f1fd20e73 ] In xdp_linearize_page, when reading the following buffers from the ring, we forget to check the received length with the true allocate size. This can lead to an out-of-bound read. This commit adds that missing check. Cc: <[email protected]> Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set") Signed-off-by: Bui Quang Minh <[email protected]> Acked-by: Jason Wang <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Michal Luczaj <[email protected]> Date: Thu Jul 3 17:18:20 2025 +0200 vsock: Fix IOCTL_VM_SOCKETS_GET_LOCAL_CID to check also `transport_local` [ Upstream commit 1e7d9df379a04ccd0c2f82f39fbb69d482e864cc ] Support returning VMADDR_CID_LOCAL in case no other vsock transport is available. Fixes: 0e12190578d0 ("vsock: add local transport support in the vsock core") Suggested-by: Stefano Garzarella <[email protected]> Reviewed-by: Stefano Garzarella <[email protected]> Signed-off-by: Michal Luczaj <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Michal Luczaj <[email protected]> Date: Thu Jul 3 17:18:19 2025 +0200 vsock: Fix transport_* TOCTOU [ Upstream commit 687aa0c5581b8d4aa87fd92973e4ee576b550cdf ] Transport assignment may race with module unload. Protect new_transport from becoming a stale pointer. This also takes care of an insecure call in vsock_use_local_transport(); add a lockdep assert. BUG: unable to handle page fault for address: fffffbfff8056000 Oops: Oops: 0000 [#1] SMP KASAN RIP: 0010:vsock_assign_transport+0x366/0x600 Call Trace: vsock_connect+0x59c/0xc40 __sys_connect+0xe8/0x100 __x64_sys_connect+0x6e/0xc0 do_syscall_64+0x92/0x1c0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Fixes: c0cfa2d8a788 ("vsock: add multi-transports support") Reviewed-by: Stefano Garzarella <[email protected]> Signed-off-by: Michal Luczaj <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Michal Luczaj <[email protected]> Date: Thu Jul 3 17:18:18 2025 +0200 vsock: Fix transport_{g2h,h2g} TOCTOU [ Upstream commit 209fd720838aaf1420416494c5505096478156b4 ] vsock_find_cid() and vsock_dev_do_ioctl() may race with module unload. transport_{g2h,h2g} may become NULL after the NULL check. Introduce vsock_transport_local_cid() to protect from a potential null-ptr-deref. KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f] RIP: 0010:vsock_find_cid+0x47/0x90 Call Trace: __vsock_bind+0x4b2/0x720 vsock_bind+0x90/0xe0 __sys_bind+0x14d/0x1e0 __x64_sys_bind+0x6e/0xc0 do_syscall_64+0x92/0x1c0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f] RIP: 0010:vsock_dev_do_ioctl.isra.0+0x58/0xf0 Call Trace: __x64_sys_ioctl+0x12d/0x190 do_syscall_64+0x92/0x1c0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Fixes: c0cfa2d8a788 ("vsock: add multi-transports support") Suggested-by: Stefano Garzarella <[email protected]> Reviewed-by: Stefano Garzarella <[email protected]> Signed-off-by: Michal Luczaj <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Nicolas Pitre <[email protected]> Date: Tue Jun 10 21:41:44 2025 -0400 vt: add missing notification when switching back to text mode [ Upstream commit ff78538e07fa284ce08cbbcb0730daa91ed16722 ] Programs using poll() on /dev/vcsa to be notified when VT changes occur were missing one case: the switch from gfx to text mode. Signed-off-by: Nicolas Pitre <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Daniil Dulov <[email protected]> Date: Thu Jun 26 14:46:19 2025 +0300 wifi: zd1211rw: Fix potential NULL pointer dereference in zd_mac_tx_to_dev() [ Upstream commit 74b1ec9f5d627d2bdd5e5b6f3f81c23317657023 ] There is a potential NULL pointer dereference in zd_mac_tx_to_dev(). For example, the following is possible: T0 T1 zd_mac_tx_to_dev() /* len == skb_queue_len(q) */ while (len > ZD_MAC_MAX_ACK_WAITERS) { filter_ack() spin_lock_irqsave(&q->lock, flags); /* position == skb_queue_len(q) */ for (i=1; i<position; i++) skb = __skb_dequeue(q) if (mac->type == NL80211_IFTYPE_AP) skb = __skb_dequeue(q); spin_unlock_irqrestore(&q->lock, flags); skb_dequeue() -> NULL Since there is a small gap between checking skb queue length and skb being unconditionally dequeued in zd_mac_tx_to_dev(), skb_dequeue() can return NULL. Then the pointer is passed to zd_mac_tx_status() where it is dereferenced. In order to avoid potential NULL pointer dereference due to situations like above, check if skb is not NULL before passing it to zd_mac_tx_status(). Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 459c51ad6e1f ("zd1211rw: port to mac80211") Signed-off-by: Daniil Dulov <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
Author: Yazen Ghannam <[email protected]> Date: Tue Jun 24 14:15:59 2025 +0000 x86/mce/amd: Fix threshold limit reset commit 5f6e3b720694ad771911f637a51930f511427ce1 upstream. The MCA threshold limit must be reset after servicing the interrupt. Currently, the restart function doesn't have an explicit check for this. It makes some assumptions based on the current limit and what's in the registers. These assumptions don't always hold, so the limit won't be reset in some cases. Make the reset condition explicit. Either an interrupt/overflow has occurred or the bank is being initialized. Signed-off-by: Yazen Ghannam <[email protected]> Signed-off-by: Borislav Petkov (AMD) <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Yazen Ghannam <[email protected]> Date: Tue Jun 24 14:15:56 2025 +0000 x86/mce: Don't remove sysfs if thresholding sysfs init fails commit 4c113a5b28bfd589e2010b5fc8867578b0135ed7 upstream. Currently, the MCE subsystem sysfs interface will be removed if the thresholding sysfs interface fails to be created. A common failure is due to new MCA bank types that are not recognized and don't have a short name set. The MCA thresholding feature is optional and should not break the common MCE sysfs interface. Also, new MCA bank types are occasionally introduced, and updates will be needed to recognize them. But likewise, this should not break the common sysfs interface. Keep the MCE sysfs interface regardless of the status of the thresholding sysfs interface. Signed-off-by: Yazen Ghannam <[email protected]> Signed-off-by: Borislav Petkov (AMD) <[email protected]> Reviewed-by: Qiuxu Zhuo <[email protected]> Reviewed-by: Tony Luck <[email protected]> Tested-by: Tony Luck <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: JP Kobryn <[email protected]> Date: Fri Jun 27 10:49:35 2025 -0700 x86/mce: Make sure CMCI banks are cleared during shutdown on Intel commit 30ad231a5029bfa16e46ce868497b1a5cdd3c24d upstream. CMCI banks are not cleared during shutdown on Intel CPUs. As a side effect, when a kexec is performed, CPUs coming back online are unable to rediscover/claim these occupied banks which breaks MCE reporting. Clear the CPU ownership during shutdown via cmci_clear() so the banks can be reclaimed and MCE reporting will become functional once more. [ bp: Massage commit message. ] Reported-by: Aijay Adams <[email protected]> Signed-off-by: JP Kobryn <[email protected]> Signed-off-by: Borislav Petkov (AMD) <[email protected]> Reviewed-by: Tony Luck <[email protected]> Reviewed-by: Qiuxu Zhuo <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Jann Horn <[email protected]> Date: Wed Jul 2 10:32:04 2025 +0200 x86/mm: Disable hugetlb page table sharing on 32-bit commit 76303ee8d54bff6d9a6d55997acd88a6c2ba63cf upstream. Only select ARCH_WANT_HUGE_PMD_SHARE on 64-bit x86. Page table sharing requires at least three levels because it involves shared references to PMD tables; 32-bit x86 has either two-level paging (without PAE) or three-level paging (with PAE), but even with three-level paging, having a dedicated PGD entry for hugetlb is only barely possible (because the PGD only has four entries), and it seems unlikely anyone's actually using PMD sharing on 32-bit. Having ARCH_WANT_HUGE_PMD_SHARE enabled on non-PAE 32-bit X86 (which has 2-level paging) became particularly problematic after commit 59d9094df3d7 ("mm: hugetlb: independent PMD page table shared count"), since that changes `struct ptdesc` such that the `pt_mm` (for PGDs) and the `pt_share_count` (for PMDs) share the same union storage - and with 2-level paging, PMDs are PGDs. (For comparison, arm64 also gates ARCH_WANT_HUGE_PMD_SHARE on the configuration of page tables such that it is never enabled with 2-level paging.) Closes: https://lore.kernel.org/r/[email protected] Fixes: cfe28c5d63d8 ("x86: mm: Remove x86 version of huge_pmd_share.") Reported-by: Vitaly Chikunov <[email protected]> Suggested-by: Dave Hansen <[email protected]> Signed-off-by: Jann Horn <[email protected]> Signed-off-by: Dave Hansen <[email protected]> Acked-by: Oscar Salvador <[email protected]> Acked-by: David Hildenbrand <[email protected]> Tested-by: Vitaly Chikunov <[email protected]> Cc:[email protected] Link: https://lore.kernel.org/all/20250702-x86-2level-hugetlb-v2-1-1a98096edf92%40google.com Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Jack Wang <[email protected]> Date: Mon Jul 14 21:36:28 2025 +0200 x86: Fix X86_FEATURE_VERW_CLEAR definition This is a mistake during backport. VERW_CLEAR is on bit 5, not bit 10. Fixes: f2b75f1368af ("x86/bugs: Add a Transient Scheduler Attacks mitigation") Cc: Borislav Petkov (AMD) <[email protected]> Signed-off-by: Jack Wang <[email protected]> Acked-by: Borislav Petkov (AMD) <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Juergen Gross <[email protected]> Date: Mon May 30 10:26:34 2022 +0200 xen: replace xen_remap() with memremap() commit 41925b105e345ebc84cedb64f59d20cb14a62613 upstream. xen_remap() is used to establish mappings for frames not under direct control of the kernel: for Xenstore and console ring pages, and for grant pages of non-PV guests. Today xen_remap() is defined to use ioremap() on x86 (doing uncached mappings), and ioremap_cache() on Arm (doing cached mappings). Uncached mappings for those use cases are bad for performance, so they should be avoided if possible. As all use cases of xen_remap() don't require uncached mappings (the mapped area is always physical RAM), a mapping using the standard WB cache mode is fine. As sparse is flagging some of the xen_remap() use cases to be not appropriate for iomem(), as the result is not annotated with the __iomem modifier, eliminate xen_remap() completely and replace all use cases with memremap() specifying the MEMREMAP_WB caching mode. xen_unmap() can be replaced with memunmap(). Reported-by: kernel test robot <[email protected]> Signed-off-by: Juergen Gross <[email protected]> Reviewed-by: Boris Ostrovsky <[email protected]> Acked-by: Stefano Stabellini <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Juergen Gross <[email protected]> Signed-off-by: Teddy Astie <[email protected]> [backport to 5.15.y] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Author: Basavaraj Natikar <[email protected]> Date: Mon Mar 4 11:13:27 2024 +0530 xhci: Allow RPM on the USB controller (1022:43f7) by default [ Upstream commit 28cbed496059fe1868203b76e9e0ef285733524d ] Enable runtime PM by default for older AMD 1022:43f7 xHCI 1.1 host as it is proven to work. Driver enables runtime PM by default for newer xHCI 1.2 host. Link: https://lore.kernel.org/all/[email protected]/ Cc: Mario Limonciello <[email protected]> Tested-by: Oleksandr Natalenko <[email protected]> Signed-off-by: Basavaraj Natikar <[email protected]> Acked-by: Mathias Nyman <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Stable-dep-of: cbc889ab0122 ("usb: xhci: quirk for data loss in ISOC transfers") Signed-off-by: Sasha Levin <[email protected]>
Author: Hongyu Xie <[email protected]> Date: Fri Jun 27 17:41:20 2025 +0300 xhci: Disable stream for xHC controller with XHCI_BROKEN_STREAMS [ Upstream commit cd65ee81240e8bc3c3119b46db7f60c80864b90b ] Disable stream for platform xHC controller with broken stream. Fixes: 14aec589327a6 ("storage: accept some UAS devices if streams are unavailable") Cc: stable <[email protected]> Signed-off-by: Hongyu Xie <[email protected]> Signed-off-by: Mathias Nyman <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>