The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ae (4)
  • >> ae (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ae
    
     - Attansic/Atheros L2 FastEthernet controller driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device miibus device ae

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_ae_load="YES"
    
     

    DESCRIPTION

    The device driver provides support for Attansic/Atheros L2 PCIe FastEthernet controllers.

    The controller supports hardware Ethernet checksum processing, hardware VLAN tag stripping/insertion and an interrupt moderation mechanism. Attansic L2 also features a 64-bit multicast hash filter.

    The driver supports the following media types:

    autoselect
    Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf5.
    10baseT/UTP
    Select 10Mbps operation.
    100baseTX
    Set 100Mbps (FastEthernet) operation.

    The driver provides support for the following media options:

    full-duplex
    Force full duplex operation.
    half-duplex
    Force half duplex operation.

    For more information on configuring this device, see ifconfig(8).  

    HARDWARE

    The driver supports Attansic/Atheros L2 PCIe FastEthernet controllers, and is known to support the following hardware:

    Other hardware may or may not work with this driver.  

    LOADER TUNABLES

    Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf5.

    hw.ae.msi_disable
    This tunable disables MSI support on the Ethernet hardware. The default value is 0.

     

    SYSCTL VARIABLES

    The driver collects a number of useful MAC counter during the work. The statistics is available via the dev.ae.%d.stats sysctl(8) tree, where %d corresponds to the controller number.  

    DIAGNOSTICS

    "ae%d: watchdog timeout."
    The device has stopped responding to the network, or there is a problem with the network connection (cable).
    "ae%d: reset timeout."
    The card reset operation has been timed out.
    "ae%d: Generating random ethernet address."
    No valid ethernet address was found neither in the controller registers not in NVRAM. Random locally administered address with ASUS OUI identifier will be used instead.

     

    SEE ALSO

    altq(4), arp(4), miibus(4), netintro(4), ng_ether4, vlan(4), ifconfig(8)  

    BUGS

    The Attansic L2 FastEthernet contoller supports DMA but do not use a descriptor based transfer mechanism via scatter-gather DMA. Thus the data should be copied to/from the controller memory on each transmit/receive. Furthermore, a lot of data alignment restrictions apply. This may introduce a high CPU load on systems with heavy network activity. Luckily enough this should not be a problem on modern hardware as L2 does not support speeds faster than 100Mbps.  

    HISTORY

    The driver and this manual page was written by An Stanislav Sedov Aq [email protected] . It first appeared in Fx 7.1 .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    LOADER TUNABLES
    SYSCTL VARIABLES
    DIAGNOSTICS
    SEE ALSO
    BUGS
    HISTORY


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру