The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

amidi (1)
  • >> amidi (1) ( Linux man: Команды и прикладные программы пользовательского уровня )
  •  

    NAME

    amidi - read from and write to ALSA RawMIDI ports
    

     

    SYNOPSIS

    amidi [-p port] [-s file | -S data] [-r file] [-d] [-t seconds] [-a]

     

    DESCRIPTION

    amidi is a command-line utility which allows to receive and send SysEx (system exclusive) data from/to external MIDI devices. It can also send any other MIDI commands.

    amidi handles only files containing raw MIDI commands, without timing information. amidi does not support Standard MIDI (.mid) files, but aplaymidi(1) and arecordmidi(1) do.

     

    OPTIONS

    Use the -h, -V, -l, or -L options to display information; or use at least one of the -s, -r, -S, or -d options to specify what data to send or receive.

    -h, --help
    Help: prints a list of options.

    -V, --version
    Prints the current version.

    -l, --list-devices
    Prints a list of all hardware MIDI ports.

    -L, --list-rawmidis
    Prints all RawMIDI definitions. (used when debugging configuration files)

    -p, --port=name
    Sets the name of the ALSA RawMIDI port to use. If this is not specified, amidi uses the default port defined in the configuration file (the default for this is port 0 on card 0, which may not exist).

    -s, --send=filename
    Sends the contents of the specified file to the MIDI port. The file must contain raw MIDI commands (e.g. a .syx file); for Standard MIDI (.mid) files, use aplaymidi(1).

    -r, --receive=filename
    Writes data received from the MIDI port into the specified file. The file will contain raw MIDI commands (such as in a .syx file); to record a Standard MIDI (.mid) file, use arecordmidi(1).

    amidi will filter out any Active Sensing bytes (FEh), unless the -a option has been given.

    -S, --send-hex=...
    Sends the bytes specified as hexadecimal numbers to the MIDI port.

    -d, --dump
    Prints data received from the MIDI port as hexadecimal bytes. Active Sensing bytes (FEh) will not be shown, unless the -a option has been given.

    This option is useful for debugging.

    -t, --timeout=seconds
    Stops receiving data when no data has been received for the specified amount of time.

    If this option has not been given, you must press Ctrl+C (or kill amidi) to stop receiving data.

    -a, --active-sensing
    Does not ignore Active Sensing bytes (FEh) when saving or printing received MIDI commands.

     

    EXAMPLES

    amidi -p hw:0 -s my_settings.syx
    will send the MIDI commands in my_settings.syx to port hw:0.

    amidi -S 'F0 43 10 4C 00 00 7E 00 F7'
    sends an XG Reset to the default port.

    amidi -p hw:1,2 -S F0411042110C000000000074F7 -r dump.syx -t 1
    sends a lqParameter Dump Requestrq to a GS device, saves the received parameter data to the file dump.syx, and stops after the device has finished sending data (when no data has been received for one second).

    amidi -p virtual -d
    creates a virtual RawMIDI port and prints all data sent to this port.

     

    FILES

    /usr/share/alsa/alsa.conf default rawmidi definitions
    /etc/asound.conf system-wide rawmidi definitions
    ~/.asoundrc user specific rawmidi definitions

     

    SEE ALSO

    aplaymidi(1)
    arecordmidi(1)

     

    AUTHOR

    Clemens Ladisch <[email protected]>


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    OPTIONS
    EXAMPLES
    FILES
    SEE ALSO
    AUTHOR


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру