The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

device_add_child (9)
  • >> device_add_child (9) ( FreeBSD man: Ядро )

  • BSD mandoc
     

    NAME

    
    
    device_add_child
    
     
    device_add_child_ordered
    
     - add a new device as a child of an existing device
    
     
    

    SYNOPSIS

       #include <sys/param.h>
       #include <sys/bus.h>
    device_t device_add_child (device_t dev const char *name int unit);
    device_t device_add_child_ordered (device_t dev int order const char *name int unit);
     

    DESCRIPTION

    Create a new child device of Fa dev . The Fa name and Fa unit arguments specify the name and unit number of the device. If the name is unknown then the caller should pass NULL If the unit is unknown then the caller should pass -1 and the system will choose the next available unit number.

    The name of the device is used to determine which drivers might be appropriate for the device. If a name is specified then only drivers of that name are probed. If no name is given then all drivers for the owning bus are probed. In any event, only the name of the device is stored so that one may safely unload/load a driver bound to that name.

    This allows busses which can uniquely identify device instances (such as PCI) to allow each driver to check each device instance for a match. For busses which rely on supplied probe hints where only one driver can have a chance of probing the device, the driver name should be specified as the device name.

    Normally unit numbers will be chosen automatically by the system and a unit number of -1 should be given. When a specific unit number is desired (e.g. for wiring a particular piece of hardware to a pre-configured unit number), that unit should be passed. If the specified unit number is already allocated, a new unit will be allocated and a diagnostic message printed.

    If the devices attached to a bus must be probed in a specific order (e.g. for the ISA bus some devices are sensitive to failed probe attempts of unrelated drivers and therefore must be probed first), the Fa order argument of device_add_child_ordered ();
    should be used to specify a partial ordering. The new device will be added before any existing device with a greater order. If device_add_child ();
    is used, then the new child will be added as if its order was zero.

    When adding a device in the context of DEVICE_IDENTIFY9 routine, the device_find_child9 routine should be used to ensure that the device has not already been added to the tree. Because the device name and Vt devclass_t are associated at probe time (not child addition time), previous instances of the driver (say in a module that was later unloaded) may have already added the instance. Authors of bus drivers must likewise be careful when adding children when they are loaded and unloaded to avoid duplication of children devices.

    Identify routines should use BUS_ADD_CHILD9 instead of device_add_child9.  

    RETURN VALUES

    The new device if successful, NULL otherwise.  

    SEE ALSO

    BUS_ADD_CHILD9, device(9), device_find_child9, DEVICE_IDENTIFY9  

    AUTHORS

    This manual page was written by An Doug Rabson .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    RETURN VALUES
    SEE ALSO
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру