The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

if_nfe (4)
  • >> if_nfe (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    nfe
    
     - NVIDIA nForce MCP Ethernet driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device miibus device nfe

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_nfe_load="YES"
    
     

    DESCRIPTION

    The driver supports PCI Ethernet adapters based on the NVIDIA nForce Media and Communications Processors (MCP), such as the nForce, nForce 2, nForce 3, CK804, MCP04, MCP51, MCP55, MCP61, MCP65, MCP67, MCP73, MCP77 and MCP79 Ethernet controller chips.

    Supported features include (hardware support provided):

    Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames.

    The driver supports the following media types:

    autoselect
    Enable autoselection of the media type and options.
    10baseT/UTP
    Set 10Mbps operation.
    100baseTX
    Set 100Mbps (Fast Ethernet) operation.
    1000baseT
    Set 1000Mbps (Gigabit Ethernet) operation (recent models only).

    The driver supports the following media options:

    half-duplex
    Force half duplex operation.
    full-duplex
    Force full duplex operation.

    For more information on configuring this device, see ifconfig(8).  

    HARDWARE

    The driver supports the following NVIDIA MCP onboard adapters:

     

    LOADER TUNABLES

    Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf5.

    hw.nfe.msi_disable
    Whether or not MSI support is enabled in the driver. The default value is 0.
    hw.nfe.msix_disable
    Whether or not MSI-X support is enabled in the driver. The default value is 0.

     

    SYSCTL VARIABLES

    The following sysctl(8) variables can be used to modify or monitor behavior.

    dev.nfe.%d.process_limit
    Maximum number of Rx events to be processed in the event loop before rescheduling a taskqueue. The accepted range is 50 to 255, the default value is 192. The interface does not need to be brought down and up again before a change takes effect.

     

    SEE ALSO

    altq(4), arp(4), intro(4), miibus(4), netintro(4), pci(4), polling(4), sysctl(8), ifconfig(8)  

    HISTORY

    The device driver first appeared in Ox 3.9 , and then in Fx 7.0 .  

    AUTHORS

    An -nosplit The driver was written by An Jonathan Gray Aq [email protected] and An Damien Bergamini Aq [email protected] . The driver was ported to Fx by An Shigeaki Tagashira Aq [email protected] .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    LOADER TUNABLES
    SYSCTL VARIABLES
    SEE ALSO
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру