Интерактивная система просмотра системных руководств (man-ов)
if_sf (4)
>> if_sf (4) ( FreeBSD man: Специальные файлы /dev/* )
BSD mandoc
NAME
sf
- Adaptec AIC-6915
Qq Starfire
PCI Fast Ethernet adapter driver
SYNOPSIS
To compile this driver into the kernel,
place the following lines in your
kernel configuration file:
device miibusdevice sf
Alternatively, to load the driver as a
module at boot time, place the following line in
loader.conf5:
if_sf_load="YES"
DESCRIPTION
The
driver provides support for Adaptec Duralink Fast Ethernet adapters
based on the Adaptec AIC-6915 "Starfire" chipset.
The AIC-6915 is a bus master controller with an MII interface.
It
supports high and low priority transmit and receive queues, TCP/IP
checksum offload, multiple DMA descriptor formats and both polling
and producer/consumer DMA models.
The AIC-6915 receive filtering
options include a 16 entry perfect filter, a 512-bit hash table
for multicast addresses, a 512-bit hash table for priority address
matching and VLAN filtering.
An external MII-compliant transceiver
is required for media interfacing.
Multiport adapters consist of several AIC-6915 controllers connected
via a PCI to PCI bridge.
Each controller is treated as a separate
interface by the
driver.
The
driver supports the following media types:
autoselect
Enable autoselection of the media type and options.
The user can manually override
the autoselected mode by adding media options to the
/etc/rc.conf
file.
10baseT/UTP
Set 10Mbps operation.
The
mediaopt
option can also be used to select either
full-duplex
or
half-duplex
modes.
100baseTX
Set 100Mbps (Fast Ethernet) operation.
The
mediaopt
option can also be used to select either
full-duplex
or
half-duplex
modes.
The
driver supports the following media options:
full-duplex
Force full duplex operation
half-duplex
Force half duplex operation.
For more information on configuring this device, see
ifconfig(8).
HARDWARE
Adapters supported by the
driver include:
ANA-62011 64-bit single port 10/100baseTX adapter
ANA-62022 64-bit dual port 10/100baseTX adapter
ANA-62044 64-bit quad port 10/100baseTX adapter
ANA-69011 32-bit single port 10/100baseTX adapter
ANA-62020 64-bit single port 100baseFX adapter
SYSCTL VARIABLES
The following variables are available as both
sysctl(8)
variables and
loader(8)
tunables:
dev.sf.%d.int_mod
Maximum amount of time to delay interrupt processing in units of
102.4us.
The accepted range is 0 to 31, the default value is 1 (102.4us).
Value 0 completely disables the interrupt moderation.
The interface does not need to be brought down and up again before
a change takes effect.
dev.sf.%d.stats
Display lots of useful MAC counters maintained in the driver.
DIAGNOSTICS
"sf%d: couldn't map memory"
A fatal initialization error has occurred.
This may
happen if the PCI BIOS not configured the device, which may be because
the BIOS has been configured for a "Plug and Play" operating system.
The "Plug and Play OS" setting in the BIOS should be set to "no" or
"off" in order for PCI devices to work properly with
Fx .
"sf%d: couldn't map ports"
A fatal initialization error has occurred.
This may
happen if the PCI BIOS not configured the device, which may be because
the BIOS has been configured for a "Plug and Play" operating system.
The "Plug and Play OS" setting in the BIOS should be set to "no" or
"off" in order for PCI devices to work properly with
Fx .
"sf%d: couldn't map interrupt"
A fatal initialization error has occurred.
"sf%d: no memory for softc struct!"
The driver failed to allocate memory for per-device instance information
during initialization.
"sf%d: failed to enable I/O ports/memory mapping!"
The driver failed to initialize PCI I/O port or shared memory access.
This might happen if the card is not in a bus-master slot.
"sf%d: watchdog timeout"
The device has stopped responding to the network, or there is a problem with
the network connection (cable).
