The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

in.tftpd (8)
  • in.tftpd (1) ( Solaris man: Команды и прикладные программы пользовательского уровня )
  • >> in.tftpd (8) ( Linux man: Команды системного администрирования )
  •  

    NAME

    tftpd
    
    - IPv4 Trivial File Transfer Protocol server
     
    

    SYNOPSIS

    in.tftpd [options...] directory...  

    DESCRIPTION

    tftpd is a server for the IPv4 Trivial File Transfer Protocol. The TFTP protocol is extensively used to support remote booting of diskless devices. The server is normally started by inetd, but can also run standalone.

     

    OPTIONS

    -l
    Run the server in standalone (listen) mode, rather than run from inetd. In listen mode, the -t option is ignored, and the -a option can be used to specify a specific local address or port to listen to.
    -a [address][:port]
    Specify a specific address and port to listen to when called with the -l option. The default is to listen to the tftp port specified in /etc/services on all local addresses.
    -c
    Allow new files to be created. By default, tftpd will only allow upload of files that already exist. Files are created with default permissions allowing anyone to read or write them, unless the -p or -U options are specified.
    -s
    Change root directory on startup. This means the remote host does not need to pass along the directory as part of the transfer, and may add security. When -s is specified, exactly one directory should be specified on the command line. The use of this option is recommended for security as well as compatibility with some boot ROMs which cannot be easily made to include a directory name in its request.
    -u username
    Specify the username which tftpd will run as; the default is "nobody". The user ID, group ID, and (if possible on the platform) the supplementary group IDs will be set to the ones specified in the system permission database for this username.
    -U umask
    Sets the umask for newly created files to the specified value. The default is zero (anyone can read or write) if the -p option is not specified, or inherited from the invoking process if -p is specified.
    -p
    Perform no additional permissions checks above the normal system-provided access controls for the user specified via the -u option.
    -t timeout
    When run from inetd this specifies how long, in seconds, to wait for a second connection before terminating the server. inetd will then respawn the server when another request comes in. The default is 900 (15 minutes.)
    -T timeout
    Determine the default timeout, in microseconds, before the first packet is retransmitted. This can be modified by the client if the timeout or utimeout option is negotiated. The default is 1000000 (1 second.)
    -m remap-file
    Specify the use of filename remapping. The remap-file is a file containing the remapping rules. See the section on filename remapping below. This option may not be compiled in, see the output of in.tftpd -V to verify whether or not it is available.
    -v
    Increase the logging verbosity of tftpd. This flag can be specified multiple times for even higher verbosity.
    -r tftp-option
    Indicate that a specific RFC 2347 TFTP option should never be accepted.
    -B max-block-size
    Specifies the maximum permitted block size. The permitted range for this parameter is from 512 to 65464. Some embedded clients request large block sizes and yet do not handle fragmented packets correctly; for these clients, it is recommended to set this value to the smallest MTU on your network minus 32 bytes (20 bytes for IP, 8 for UDP, and 4 for TFTP; less if you use IP options on your network.) For example, on a standard Ethernet (MTU 1500) a value of 1468 is reasonable.
    -V
    Print the version number and configuration to standard output, then exit gracefully.
     

    RFC 2347 OPTION NEGOTIATION

    This version of tftpd supports RFC 2347 option negotation. Currently implemented options are:
    blksize (RFC 2348)
    Set the transfer block size to anything less than or equal to the specified option. This version of tftpd can support any block size up to the theoretical maximum of 65464 bytes.
    blksize2 (nonstandard)
    Set the transfer block size to anything less than or equal to the specified option, but restrict the possible responses to powers of 2. The maximum is 32768 bytes (the largest power of 2 less than or equal to 65464.)
    tsize (RFC 2349)
    Report the size of the file that is about to be transferred. This version of tftpd only supports the tsize option for binary (octet) mode transfers.
    timeout (RFC 2349)
    Set the time before the server retransmits a packet, in seconds.
    utimeout (nonstandard)
    Set the time before the server retransmits a packet, in microseconds.

    The -r option can be used to disable specific options; this may be necessary to work around bugs in specific TFTP client implementations. For example, some TFTP clients have been found to request the blksize option, but crash with an error if they actually get the option accepted by the server.  

    FILENAME REMAPPING

    The -m option specifies a file which contains filename remapping rules. Each non-comment line (comments begin with hash marks, #) contains an operation, specified below; a regex, a regular expression in the style of egrep; and optionally a replacement pattern. The operation indicated by operation is performed if the regex matches all or part of the filename. Rules are processed from the top down, and by default, all rules are processed even if there is a match.

    The operation can be any combination of the following letters:

    r
    Replace the substring matched by regex by the replacement pattern. The replacement pattern may contain escape sequences; see below.
    g
    Repeat this rule until it no longer matches. This is always used with r.
    i
    Match the regex case-insensitively. By default it is case sensitive.
    e
    If this rule matches, end rule processing after executing the rule.
    s
    If this rule matches, start rule processing over from the very first rule after executing this rule.
    a
    If this rule matches, refuse the request and send an access denied error to the client.
    G
    This rule applies to GET (RRQ) requests only.
    P
    This rule applies to PUT (WRQ) requests only.

    The following escape sequences are recognized as part of the replacement pattern:

    \0
    The entire string matched by the regex.
    \1 to \9
    The strings matched by each of the first nine parenthesized subexpressions, \( ... \), of the regex pattern.
    \i
    The IP address of the requesting host, in dotted-quad notation (e.g. 192.0.2.169).
    \x
    The IP address of the requesting host, in hexadecimal notation (e.g. C00002A9).
    \\
    Literal backslash.
    \whitespace
    Literal whitespace.
    \#
    Literal hash mark.

    If the mapping file is changed, you need to send SIGHUP to any outstanding tftpd process.  

    SECURITY

    The use of TFTP services does not require an account or password on the server system. Due to the lack of authentication information, tftpd will allow only publicly readable files (o+r) to be accessed, unless the -p option is specified. Files may be written only if they already exist and are publicly writable, unless the -c option is specified. Note that this extends the concept of ``public'' to include all users on all hosts that can be reached through the network; this may not be appropriate on all systems, and its implications should be considered before enabling TFTP service. Typically, some kind of firewall or packet-filter solution should be employed. If appropriately compiled (see the output of in.tftpd -V) tftpd will query the hosts_access(5) database for access control information. This may be slow; sites requiring maximum performance may want to compile without this option and rely on firewalling or kernel-based packet filters instead.

    The server should be set to run as the user with the lowest possible privilege; please see the -u flag. It is probably a good idea to set up a specific user account for tftpd, rather than letting it run as "nobody", to guard against privilege leaks between applications.

    Access to files can, and should, be restricted by invoking tftpd with a list of directories by including pathnames as server program arguments on the command line. In this case access is restricted to files whole names are prefixed by one of the given directories. If possible, it is recommended that the -s flag is used to set up a chroot() environment for the server to run in once a connection has been set up.

    Finally, the filename remapping (-m flag) support can be used to provide a limited amount of additional access control.  

    CONFORMING TO

    RFC 1123, Requirements for Internet Hosts - Application and Support.
    RFC 1350, The TFTP Protocol (revision 2).
    RFC 2347, TFTP Option Extension.
    RFC 2348, TFTP Blocksize Option.
    RFC 2349, TFTP Timeout Interval and Transfer Size Options.  

    AUTHOR

    This version of tftpd is maintained by H. Peter Anvin <[email protected]>. It was derived from, but has substantially diverged from, an OpenBSD source base, with added patches by Markus Gutschke and Gero Kulhman.  

    SEE ALSO

    tftp(1), egrep(1), umask(2), hosts_access(5), regex(7), inetd(8).


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    OPTIONS
    RFC 2347 OPTION NEGOTIATION
    FILENAME REMAPPING
    SECURITY
    CONFORMING TO
    AUTHOR
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру