The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

lagg (4)
  • >> lagg (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    lagg
    
     - link aggregation and link failover interface
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following line in your kernel configuration file:
    device lagg

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_lagg_load="YES"
    
     

    DESCRIPTION

    The interface allows aggregation of multiple network interfaces as one virtual interface for the purpose of providing fault-tolerance and high-speed links.

    A interface can be created using the ifconfig lagg N create command. It can use different link aggregation protocols specified using the laggproto proto option. Child interfaces can be added using the laggport child-iface option and removed using the -laggport child-iface option.

    The driver currently supports the aggregation protocols failover (the default), fec lacp loadbalance roundrobin and none The protocols determine which ports are used for outgoing traffic and whether a specific port accepts incoming traffic. The interface link state is used to validate if the port is active or not.

    failover
    Sends and receives traffic only through the master port. If the master port becomes unavailable, the next active port is used. The first interface added is the master port; any interfaces added after that are used as failover devices.
    fec
    Supports Cisco EtherChannel. This is a static setup and does not negotiate aggregation with the peer or exchange frames to monitor the link.
    lacp
    Supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol. LACP will negotiate a set of aggregable links with the peer in to one or more Link Aggregated Groups. Each LAG is composed of ports of the same speed, set to full-duplex operation. The traffic will be balanced across the ports in the LAG with the greatest total speed, in most cases there will only be one LAG which contains all ports. In the event of changes in physical connectivity, Link Aggregation will quickly converge to a new configuration.
    loadbalance
    Balances outgoing traffic across the active ports based on hashed protocol header information and accepts incoming traffic from any active port. This is a static setup and does not negotiate aggregation with the peer or exchange frames to monitor the link. The hash includes the Ethernet source and destination address, and, if available, the VLAN tag, and the IP source and destination address.
    roundrobin
    Distributes outgoing traffic using a round-robin scheduler through all active ports and accepts incoming traffic from any active port.
    none
    This protocol is intended to do nothing: it disables any traffic without disabling the interface itself.

    Each interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf5.

    The MTU of the first interface to be added is used as the lagg MTU. All additional interfaces are required to have exactly the same value.  

    EXAMPLES

    Create a 802.3ad link aggregation using LACP with two bge(4) Gigabit Ethernet interfaces:
    # ifconfig bge0 up
    # ifconfig bge1 up
    # ifconfig lagg0 laggproto lacp laggport bge0 laggport bge1 \
            192.168.1.1 netmask 255.255.255.0
    

    The following example uses an active failover interface to set up roaming between wired and wireless networks using two network devices. Whenever the wired master interface is unplugged, the wireless failover device will be used:

    # ifconfig em0 up
    # ifconfig ath0 nwid my_net up
    # ifconfig lagg0 laggproto failover laggport em0 laggport ath0 \
            192.168.1.1 netmask 255.255.255.0
    
     

    SEE ALSO

    ng_fec4, ng_one2many4, ifconfig(8)  

    HISTORY

    The device first appeared in Fx 6.3 .  

    AUTHORS

    An -nosplit The driver was written under the name trunk by An Reyk Floeter Aq [email protected] . The LACP implementation was written by An YAMAMOTO Takashi for Nx .  

    BUGS

    There is no way to configure LACP administrative variables, including system and port priorities. The current implementation always performs active-mode LACP and uses 0x8000 as system and port priorities.

    WPA security does not currently work correctly with a wireless interface added to the lagg port.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    EXAMPLES
    SEE ALSO
    HISTORY
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру