The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

lge (4)
  • >> lge (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    lge
    
     - Level 1 LXT1001 NetCellerator PCI Gigabit Ethernet adapter driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device miibus device lge

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_lge_load="YES"
    
     

    DESCRIPTION

    The driver provides support for various NICs based on the Level 1 LXT1001 NetCellerator Gigabit Ethernet controller chip.

    The LXT1001 supports fiber PHYs and also a GMII port for use with 10/100/1000 copper PHYs, however there are currently no NICs on the market that use this feature.

    The LXT1001 supports TCP/IP checksum offload for receive and VLAN-based filtering as well as a 64-bit multicast hash filter. It also supports jumbo frames, which can be configured via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit jumbo frames. Using jumbo frames can greatly improve performance for certain tasks, such as file transfers and data streaming.

    The driver supports the following media types:

    autoselect
    Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf5.
    1000baseSX
    Set 1000baseSX operation over fiber optic cable. Both full-duplex and half-duplex modes are supported.

    The driver supports the following media options:

    full-duplex
    Force full duplex operation.
    half-duplex
    Force half duplex operation.

    For more information on configuring this device, see ifconfig(8).  

    HARDWARE

    Adapters supported by the driver include:

     

    DIAGNOSTICS

    "lge%d: couldn't map memory"
    A fatal initialization error has occurred.
    "lge%d: couldn't map ports"
    A fatal initialization error has occurred.
    "lge%d: couldn't map interrupt"
    A fatal initialization error has occurred.
    "lge%d: no memory for softc struct!"
    The driver failed to allocate memory for per-device instance information during initialization.
    "lge%d: failed to enable memory mapping!"
    The driver failed to initialize PCI shared memory mapping. This might happen if the card is not in a bus-master slot.
    "lge%d: no memory for jumbo buffers!"
    The driver failed to allocate memory for jumbo frames during initialization.
    "lge%d: watchdog timeout"
    The device has stopped responding to the network, or there is a problem with the network connection (cable).

     

    SEE ALSO

    arp(4), miibus(4), netintro(4), ng_ether4, ifconfig(8)
    Level 1 LXT1001 Programming Manual http://www.FreeBSD.org/~wpaul/Level1/LXT1001SRM.pdf
     

    HISTORY

    The device driver first appeared in Fx 4.4 .  

    AUTHORS

    The driver was written by An Bill Paul Aq [email protected] .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    DIAGNOSTICS
    SEE ALSO
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру