The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

mlx (4)
  • >> mlx (4) ( FreeBSD man: Специальные файлы /dev/* )
  • mlx (7) ( Solaris man: Макропакеты и соглашения )

  • BSD mandoc
     

    NAME

    
    
    mlx
    
     - Mylex DAC-family RAID driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device pci device mlx

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    mlx_load="YES"
    
     

    DESCRIPTION

    The driver provides support for Mylex DAC-family PCI to SCSI RAID controllers, including versions relabeled by Digital/Compaq.  

    HARDWARE

    Controllers supported by the driver include:

    All major firmware revisions (2.x, 3.x, 4.x and 5.x) are supported, however it is always advisable to upgrade to the most recent firmware available for the controller.

    Compatible Mylex controllers not listed should work, but have not been verified.  

    DIAGNOSTICS

     

    Controller initialisation phase

    mlx%d: controller initialisation in progress...
    mlx%d: initialisation complete

    The controller firmware is performing/has completed initialisation.

    mlx%d: physical drive %d:%d not responding

    The drive at channel:target is not responding; it may have failed or been removed.

    mlx%d: spinning up drives...

    Drive startup is in progress; this may take several minutes.

    mlx%d: configuration checksum error

    The array configuration has become corrupted.

    mlx%d: mirror race recovery in progress
    mlx%d: mirror race on a critical system drive
    mlx%d: mirror race recovery failed

    These error codes are undocumented.

    mlx%d: physical drive %d:%d COD mismatch

    Configuration data on the drive at channel:target does not match the rest of the array.

    mlx%d: system drive installation aborted

    Errors occurred preventing one or more system drives from being configured.

    mlx%d: new controller configuration found

    The controller has detected a configuration on disk which supersedes the configuration in its nonvolatile memory. It will reset and come up with the new configuration.

    mlx%d: FATAL MEMORY PARITY ERROR

    Firmware detected a fatal memory error; the driver will not attempt to attach to this controller.

    mlx%d: unknown firmware initialisation error %x:%x:%x

    An unknown error occurred during initialisation; it will be ignored.

     

    Driver initialisation/shutdown phase:

    mlx%d: can't allocate scatter/gather DMA tag
    mlx%d: can't allocate buffer DMA tag
    mlx%d: can't allocate s/g table
    mlx%d: can't make initial s/g list mapping
    mlx%d: can't make permanent s/g list mapping
    mlx%d: can't allocate interrupt
    mlx%d: can't set up interrupt

    A resource allocation error occurred while initialising the driver; initialisation has failed and the driver will not attach to this controller.

    mlx%d: error fetching drive status

    The current status of all system drives could not be fetched; attachment of system drives will be aborted.

    mlx%d: device_add_child failed
    mlx%d: bus_generic_attach returned %d

    Creation of the system drive instances failed; attachment of one or more system drives may have been aborted.

    mlxd%d: detaching...

    The indicated system drive is being detached.

    mlxd%d: still open, can't detach

    The indicated system drive is still open or mounted; the controller cannot be detached.

    mlx%d: flushing cache...

    The controller cache is being flushed prior to detach or shutdown.

     

    Operational diagnostics:

    mlx%d: ENQUIRY failed - %s
    mlx%d: ENQUIRY2 failed
    mlx%d: ENQUIRY_OLD failed
    mlx%d: FLUSH failed - %s
    mlx%d: CHECK ASYNC failed - %s
    mlx%d: REBUILD ASYNC failed - %s
    mlx%d: command failed - %s

    The controller rejected a command for the reason given.

    mlx%d: I/O beyond end of unit (%u,%d > %u)
    mlx%d: I/O error - %s

    An I/O error was reported by the controller.

    mlx%d: periodic enquiry failed - %s

    An attempt to poll the controller for status failed for the reason given.

    mlx%d: mlx_periodic_enquiry: unknown command %x

    The periodic status poll has issued a command which has become corrupted.

    mlxd%d: drive offline
    mlxd%d: drive online
    mlxd%d: drive critical

    The system disk indicated has changed state.

    mlx%d: physical drive %d:%d reset
    mlx%d: physical drive %d:%d killed %s
    "mlx%d: physical drive %d:%d error log: sense = %d asc = %x asq = %x"
    "mlx%d: info %4D csi %4D"

    The drive at channel:target has been reset, killed for the given reason, or experienced a SCSI error.

    mlx%d: unknown log message type %x
    mlx%d: error reading message log - %s

    An error occurred while trying to read the controller's message log.

    mlxd%d: consistency check started
    mlx%d: consistency check completed

    A user-initiated consistency check has started/completed.

    mlx%d: drive rebuild started for %d:%d
    mlx%d: drive rebuild completed

    A user-initiated physical drive rebuild has started/completed.

    mlx%d: background check/rebuild operation started
    mlx%d: background check/rebuild operation completed

    An automatic system drive consistency check or physical drive rebuild has started/completed.

    mlx%d: channel %d pausing for %d seconds
    mlx%d: channel %d resuming
    mlx%d: pause command failed - %s
    mlx%d: pause failed for channel %d
    mlx%d: resume command failed - %s
    mlx%d: resume failed for channel %d

    Controller/channel pause operation notification. (Channel pause is not currently supported on any controller.)

    mlx%d: controller wedged (not taking commands)

    The controller is not responding to attempts to submit new commands.

    mlx%d: duplicate done event for slot %d
    mlx%d: done event for nonbusy slot %d

    Corruption has occurred in either the controller's onboard list of commands or in the driver.

     

    SEE ALSO

    mlxcontrol(8)  

    AUTHORS

    An -nosplit The driver was written by An Michael Smith Aq [email protected] .

    This manual page was written by An Jeroen Ruigrok van der Werven Aq [email protected] and An Michael Smith Aq [email protected] .  

    BUGS

    The driver does not yet support EISA adapters. The DEC KZPSC has insufficient flash ROM to hold any reasonably recent firmware. This has caused problems for this driver.

    The driver does not yet support the version 6.x firmware as found in the AcceleRAID 352 and eXtremeRAID 2000 and 3000 products.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    DIAGNOSTICS
    Controller initialisation phase
    Driver initialisation/shutdown phase:
    Operational diagnostics:
    SEE ALSO
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру