The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ng_tty (4)
  • >> ng_tty (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ng_tty
    
     - netgraph node type that is also a line discipline
    
     
    

    SYNOPSIS

       #include <sys/types.h>
       #include <sys/ttycom.h>
       #include <netgraph/ng_tty.h>
     

    DESCRIPTION

    The tty node type is both a netgraph node type and a line discipline. A new node is created when the corresponding line discipline, NETGRAPHDISC is registered on a tty device (see tty(4)).

    The node has a single hook called hook Incoming bytes received on the tty device are sent out on this hook, and frames received on hook are transmitted out on the tty device. No modification to the data is performed in either direction. While the line discipline is installed on a tty, the normal read and write operations are unavailable, returning Er EIO .

    The node supports an optional ``hot character'' If set to non-zero, incoming data from the tty device is queued until this character is seen. This avoids sending lots of mbufs containing a small number of bytes, but introduces potentially infinite latency. The default hot character is 0x7e, consistent with hook being connected to a ng_async4 type node. The hot character has no effect on the transmission of data.

    The node will attempt to give itself the same netgraph name as the name of the tty device. In any case, information about the node is available via the netgraph ioctl(2) command NGIOCGINFO This command returns a struct nodeinfo similar to the NGM_NODEINFO netgraph control message.  

    HOOKS

    This node type supports the following hooks:

    hook
    tty(4) serial data contained in mbuf structures, with arbitrary inter-frame boundaries.

     

    CONTROL MESSAGES

    This node type supports the generic control messages, plus the following:

    NGM_TTY_SET_HOTCHAR
    This command takes an integer argument and sets the hot character from the lower 8 bits. A hot character of zero disables queueing, so that all received data is forwarded immediately.
    NGM_TTY_GET_HOTCHAR
    Returns an integer containing the current hot character in the lower eight bits.

     

    SHUTDOWN

    This node shuts down when the corresponding device is closed (or the line discipline is uninstalled on the device). The NGM_SHUTDOWN control message is not valid, and always returns the error Er EOPNOTSUPP .  

    SEE ALSO

    ioctl(2), netgraph(4), ng_async4, tty(4), ngctl(8)  

    HISTORY

    The node type was implemented in Fx 4.0 .  

    AUTHORS

    An Archie Cobbs Aq [email protected]  

    BUGS

    The serial driver code also has a notion of a ``hot character'' Unfortunately, this value is statically defined in terms of the line discipline and cannot be changed. Therefore, if a hot character other than 0x7e (the default) is set for the node, the node has no way to convey this information to the serial driver, and sub-optimal performance may result.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HOOKS
    CONTROL MESSAGES
    SHUTDOWN
    SEE ALSO
    HISTORY
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру