The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

pbio (4)
  • >> pbio (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    pbio
    
     - 8255 parallel peripheral interface basic
    
    I/O
    
    driver
     
    

    SYNOPSIS

    device pbio

    In /boot/device.hints hint.pbio.0.at=isa hint.pbio.0.port=0x360

       #include <dev/pbio/pbioio.h>
     

    DESCRIPTION

    The driver supports direct access to the Intel 8255A programmable peripheral interface (PPI) chip running in mode 0 (simple I/O ) Such an interface provides 24 digital I/O lines. The driver is designed for performing I/O under program control using peripherals such as the Advantech PCL-724 card, which emulates the Intel 8255A PPI in mode 0. Other 8255A-based peripherals such as the BMC Messsysteme PIO24II card have also been reported to work.

    The PPI provides two 8-bit ports (port A and port B) and two 4-bit ports (port C upper, port C lower). Each port can be individually programmed for input and (latched) output, and appears at a different offset of the device's base I/O address.

    A separate register allows the configuration of ports for input or output. The device is so simple, that reliably probing for it when input data arrives at its terminals is impossible; therefore the kernel configuration has to specify the device's base address. The device driver provides four character devices that correspond to the peripheral's I/O ports. Opening a device for read or write automatically configures the corresponding hardware port for input or output. At boot time all ports are set configured for input to avoid damaging external circuitry.

    A set of ioctl(2) requests allow polled input and paced output to be efficiently performed at the driver level without expensive user/kernel context switching. The driver can perform I/O in three different ways:

    Basic
    The read or write operation returns immediately after reading or writing the data to the port at bus speed.
    Paced
    Data is transferred from or to the port at intervals specified by a separate ioctl(2) call.
    Differential
    (Input only.) Only port values that differ from the previous port value are returned.

    The pacing interval is specified in Hz unit increments. Setting a pace of n seconds will result in no more than one value being read or written every n seconds. Single byte read/write operations will take at least n seconds to complete.

    The following ioctl(2) calls are supported:

    PBIO_SETDIFF
    accepts a pointer to an integer as the third argument, and sets the driver for differential input if the integer is non-zero. The input pace speed determines the periodic interval the driver will use to examine the port for a changed value.
    PBIO_GETDIFF
    accepts a pointer to an integer as the third argument, and sets the integer to the last set value for differential input.
    PBIO_SETIPACE
    accepts a pointer to an integer as the third argument, and sets the driver's input pacing speed to the value of that integer.
    PBIO_GETIPACE
    accepts a pointer to an integer as the third argument, and sets the integer to the last set value for the input pace.
    PBIO_SETOPACE
    accepts a pointer to an integer as the third argument, and sets the driver's output pacing speed to the value of that integer.
    PBIO_GETOPACE
    accepts a pointer to an integer as the third argument, and sets the integer to the last set value for the output pace.

     

    FILES

    /dev/pbio0a
    Port A (8 bit I/O )
    /dev/pbio0b
    Port B (8 bit I/O )
    /dev/pbio0ch
    Port C upper (4 bit I/O )
    /dev/pbio0cl
    Port C lower (4 bit I/O )

     

    SEE ALSO

    "Diomidis Spinellis" "The information furnace: Consolidated home control" "2003" "Personal and Ubiquitous Computing" 1 7 "53-69"
     

    HISTORY

    The device was first used under Fx 4.1 .  

    AUTHORS

    An Diomidis D. Spinellis Aq [email protected]  

    BUGS

    One of the PCL-724 card's inputs can optionally be wired to generate an interrupt. This feature is not supported.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    FILES
    SEE ALSO
    HISTORY
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру