The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

rfcomm (1)
  • >> rfcomm (1) ( Linux man: Команды и прикладные программы пользовательского уровня )
  •  

    NAME

    rfcomm - RFCOMM configuration utility
     
    

    SYNOPSIS

    rfcomm [ options ] < command > < dev >  

    DESCRIPTION

    rfcomm is used to set up, maintain, and inspect the RFCOMM configuration of the Bluetooth subsystem in the Linux kernel. If no command is given, or if the option -a is used, rfcomm prints information about the configured RFCOMM devices.  

    OPTIONS

    -h
    Gives a list of possible commands.
    -a
    Prints information about all configured RFCOMM devices.
    -r
    Switch TTY into raw mode (doesn't work with "bind").
    -f <file>
    Specify alternate config file.
    -i <hciX> | <bdaddr>
    The command is applied to device -A Enable authentication. -E Enable encryption. -S Secure connection. -M Become the master of a piconet. hciX , which must be the name or the address of an installed Bluetooth device. If not specified, the command will be use the first available Bluetooth device.
    -A
    Enable authentification
    -E
    Enable encryption
    -S
    Secure connection
    -M
    Become the master of a piconet
    -L <seconds>
    Set linger timeout
     

    COMMANDS

    show <dev>
    Display the information about the specified device.
    connect <dev> [bdaddr] [channel]
    Connect the RFCOMM device to the remote Bluetooth device on the specified channel. If no channel is specified, it will use the channel number 1. If also the Bluetooth address is left out, it tries to read the data from the config file. This command can be terminated with the key sequence CTRL-C.
    listen <dev> [channel] [cmd]
    Listen on a specified RFCOMM channel for incoming connections. If no channel is specified, it will use the channel number 1, but a channel must be specified before cmd. If cmd is given, it will be executed as soon as a client connects. When the child process terminates or the client disconnect, the command will terminate. Occurences of {} in cmd will be replaced by the name of the device used by the connection. This command can be terminated with the key sequence CTRL-C.
    watch <dev> [channel] [cmd]
    Watch is identical to listen except that when the child process terminates or the client disconnect, the command will restart listening with the same parameters.
    bind <dev> [bdaddr] [channel]
    This binds the RFCOMM device to a remote Bluetooth device. The command did not establish a connection to the remote device, it only creates the binding. The connection will be established right after an application tries to open the RFCOMM device. If no channel number is specified, it uses the channel number 1. If the Bluetooth address is also left out, it tries to read the data from the config file.

    If all is specified for the RFCOMM device, then all devices that have bind yes set in the config will be bound.

    release <dev>
    This command releases a defined RFCOMM binding.

    If all is specified for the RFCOMM device, then all bindings will be removed. This command didn't care about the settings in the config file.

     

    AUTHOR

    Written by Marcel Holtmann <[email protected]>.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    OPTIONS
    COMMANDS
    AUTHOR


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру