The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

sa (4)
  • >> sa (4) ( FreeBSD man: Специальные файлы /dev/* )
  • sa (8) ( FreeBSD man: Команды системного администрирования )
  • sa (8) ( Linux man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    sa
    
     - SCSI Sequential Access device driver
    
     
    

    SYNOPSIS

    device sa  

    DESCRIPTION

    The driver provides support for all SCSI devices of the sequential access class that are attached to the system through a supported SCSI Host Adapter. The sequential access class includes tape and other linear access devices.

    A SCSI Host adapter must also be separately configured into the system before a SCSI sequential access device can be configured.  

    MOUNT SESSIONS

    The driver is based around the concept of a ``mount session '' which is defined as the period between the time that a tape is mounted, and the time when it is unmounted. Any parameters set during a mount session remain in effect for the remainder of the session or until replaced. The tape can be unmounted, bringing the session to a close in several ways. These include:

    1. Closing a `rewind device', referred to as sub-mode 00 below. An example is /dev/sa0
    2. Using the MTOFFL ioctl(2) command, reachable through the `offline ' command of mt(1).

    It should be noted that tape devices are exclusive open devices, except in the case where a control mode device is opened. In the latter case, exclusive access is only sought when needed (e.g., to set parameters).  

    SUB-MODES

    Bits 0 and 1 of the minor number are interpreted as `sub-modes' The sub-modes differ in the action taken when the device is closed:

    00
    A close will rewind the device; if the tape has been written, then a file mark will be written before the rewind is requested. The device is unmounted.
    01
    A close will leave the tape mounted. If the tape was written to, a file mark will be written. No other head positioning takes place. Any further reads or writes will occur directly after the last read, or the written file mark.
    10
    A close will rewind the device. If the tape has been written, then a file mark will be written before the rewind is requested. On completion of the rewind an unload command will be issued. The device is unmounted.

     

    BLOCKING MODES

    SCSI tapes may run in either `variable ' or `fixed ' block-size modes. Most QIC -type devices run in fixed block-size mode, where most nine-track tapes and many new cartridge formats allow variable block-size. The difference between the two is as follows:

    Variable block-size:
    Each write made to the device results in a single logical record written to the tape. One can never read or write part of a record from tape (though you may request a larger block and read a smaller record); nor can one read multiple blocks. Data from a single write is therefore read by a single read. The block size used may be any value supported by the device, the SCSI adapter and the system (usually between 1 byte and 64 Kbytes, sometimes more).

    When reading a variable record/block from the tape, the head is logically considered to be immediately after the last item read, and before the next item after that. If the next item is a file mark, but it was never read, then the next process to read will immediately hit the file mark and receive an end-of-file notification.

    Fixed block-size:
    Data written by the user is passed to the tape as a succession of fixed size blocks. It may be contiguous in memory, but it is considered to be a series of independent blocks. One may never write an amount of data that is not an exact multiple of the blocksize. One may read and write the same data as a different set of records. In other words, blocks that were written together may be read separately, and vice-versa.

    If one requests more blocks than remain in the file, the drive will encounter the file mark. As there is some data to return (unless there were no records before the file mark), the read will succeed, returning that data. The next read will return immediately with a value of 0. (As above, if the file mark is never read, it remains for the next process to read if in no-rewind mode.)

     

    FILE MARK HANDLING

    The handling of file marks on write is automatic. If the user has written to the tape, and has not done a read since the last write, then a file mark will be written to the tape when the device is closed. If a rewind is requested after a write, then the driver assumes that the last file on the tape has been written, and ensures that there are two file marks written to the tape. The exception to this is that there seems to be a standard (which we follow, but do not understand why) that certain types of tape do not actually write two file marks to tape, but when read, report a `phantom' file mark when the last file is read. These devices include the QIC family of devices. (It might be that this set of devices is the same set as that of fixed block devices. This has not been determined yet, and they are treated as separate behaviors by the driver at this time.)  

    IOCTLS

    The driver supports all of the ioctls of mtio(4).  

    FILES

    /dev/[n][e]sa[0-9]
    general form:
    /dev/sa0
    Rewind on close
    /dev/nsa0
    No rewind on close
    /dev/esa0
    Eject on close (if capable)
    /dev/sa0.ctl
    Control mode device (to examine state while another program is accessing the device, e.g.).

     

    DIAGNOSTICS

    None.  

    SEE ALSO

    mt(1), scsi(4)  

    AUTHORS

    An -nosplit The driver was written for the CAM SCSI subsystem by An Justin T. Gibbs and An Kenneth Merry . Many ideas were gleaned from the st device driver written and ported from Mach 2.5 by An Julian Elischer .

    The current owner of record is An Matthew Jacob who has suffered too many years of breaking tape drivers.  

    BUGS

    This driver lacks many of the hacks required to deal with older devices. Many older SCSI-1 devices may not work properly with this driver yet.

    Additionally, certain tapes (QIC tapes mostly) that were written under Fx 2.X are not automatically read correctly with this driver: you may need to explicitly set variable block mode or set to the blocksize that works best for your device in order to read tapes written under Fx 2.X.

    Fine grained density and compression mode support that is bound to specific device names needs to be added.

    Support for fast indexing by use of partitions is missing.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    MOUNT SESSIONS
    SUB-MODES
    BLOCKING MODES
    FILE MARK HANDLING
    IOCTLS
    FILES
    DIAGNOSTICS
    SEE ALSO
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру