The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

targ (4)
  • >> targ (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    targ
    
     - SCSI target emulator driver
    
     
    

    SYNOPSIS

    device targ  

    DESCRIPTION

    The driver provides an interface for usermode programs to emulate SCSI target devices. A sample program that emulates a disk drive (similar to da(4)) can be found in /usr/share/examples/scsi_target

    The driver supplies control devices, /dev/targ0 /dev/targ1 etc. If a device is already in use, open(2) will fail and errno will be set to Er EBUSY . After opening the device, the file descriptor must be bound to a specific bus/target/LUN and enabled to process CCBs using the TARGIOCENABLE ioctl. The process then uses write(2) to send CCBs to the SIM and poll(2) or kqueue(2) to see if responses are ready. Pointers to completed CCBs are returned via read(2). Any data transfers requested by the user CCBs are done via zero-copy IO.  

    IOCTLS

    The following ioctl(2) calls are defined in the header file In cam/scsi/scsi_targetio.h .

    TARGIOCENABLE
    (Vt struct ioc_enable_lun ) Enable target mode on the LUN specified by the following structure:
    struct ioc_enable_lun {
            path_id_t       path_id;
            target_id_t     target_id;
            lun_id_t        lun_id;
            int             grp6_len;
            int             grp7_len;
    };
    

    The selected path (bus), target, and LUN must not already be in use or Er EADDRINUSE is returned. If grp6_len or grp7_len are non-zero, reception of vendor-specific commands is enabled.

    TARGIOCDISABLE
    Disable target mode and abort all pending CCBs. The CCBs may optionally be read as they complete. TARGIOCENABLE can then be called to activate a different LUN. Multiple disable calls have no effect. The close(2) system call automatically disables target mode if enabled.
    TARGIOCDEBUG
    (Vt int ) Enables CAM_PERIPH debugging if the argument is non-zero, otherwise disables it.

     

    FILES

    In cam/scsi/scsi_targetio.h
    describes the usermode interface.
    /sys/cam/scsi/scsi_target.c
    is the driver source file.
    /dev/targ*
    are the control devices.

     

    SEE ALSO

    /usr/share/examples/scsi_target ahc(4), isp(4), scsi(4)
    "FreeBSD Target Information" http://www.root.org/~nate/freebsd/
     

    AUTHORS

    An -nosplit The driver first appeared in Fx 3.0 and was written by An Justin T. Gibbs . It was rewritten for Fx 5.0 by An Nate Lawson Aq [email protected] .  

    BUGS

    Currently, only the ahc(4) and isp(4) drivers fully support target mode.

    The ahc(4) driver does not support tagged queuing in target mode.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    IOCTLS
    FILES
    SEE ALSO
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру